- 您现在的位置：买卖IC网 > PDF目录383341 > MAX1925 (Maxim Integrated Products, Inc.) Fixed-Point Digital Signal Processor 548-FCBGA PDF资料下载
参数资料
| 型号： | MAX1925 |
| 厂商： | Maxim Integrated Products, Inc. |
| 元件分类： | 数字信号处理 |
| 英文描述： | Fixed-Point Digital Signal Processor 548-FCBGA |
| 中文描述： | 开关模式单节Li+电池充电器 |
| 文件页数： | 11/16页 |
| 文件大小： | 443K |
| 代理商： | MAX1925 |
linear 4mA current source (PREQUAL1). When the cell
voltage exceeds 2V, the cell is charged with 10% of the
programmed fast-charge current (I
FASTCHG
) until it
reaches 3V. When the cell voltage is above 3V, fast
charging occurs at the full set current. If the cell fails to
reach the next prequalification threshold before a set
time (see t
PREQUAL1
and t
PREQUAL2
in the
Timer
Capacitor and Fault Modes
section), charging stops, a
fault alarm is set, and the
CHG
output blinks.
Figures 2 and 3 show charging behavior typical Li+ cell.
The MAX1925/MAX1926 remain in fast-charge mode
until the battery voltage reaches regulation and the
charge current drops below 1/8th of I
FASTCHG
. The
charger then enters full topoff mode and the
CHG
LED
is turned off. In full topoff mode, the controller continues
to operate as in fast-charge mode, except that it
remains in constant-voltage mode (CVM) unless the bat-
tery voltage falls. After every t
PREQUAL1
(see the
Timer
Capacitor and Fault Modes
section) the charger enters
the Kelvin state (for 2 CT clock cycles, 60ms with C
CT
=
100nF) where charge current is interrupted so that the
battery voltage can be accurately measured.
The MAX1925/MAX1926 do not enter done mode until
t
FULLCHG
has been reached. If the battery is removed
M
Switch-Mode 1-Cell Li+ Chargers
______________________________________________________________________________________
11
CVM
1V
2V
3V
4V
4mA
C/10
C
C/8
PREQUAL1
CHARGE CURRENT
C
1V
2V
3V
4V
C
2mA
C/10
C
C
t
t
PREQUAL2
= t/16
4.2V
C/8
FAULT
NORMAL VOLTAGE
PROFILE
NORMAL
CURRENT
PROFILE
FASTCHG
FULL TOPOFF
CCM
CVM
CCM
FASTCHG
PREQUAL2
FAULT
t
PREQUAL1
= t/1024
CHARGE TIME (t
FULLCHG
= 3 HOURS WITH C
CT
= 100nF)
CHG LED OFF
CHG LED OFF
Figure 3. Charging Current and Voltage Timing Diagrams
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1926 | Switch-Mode 1-Cell Li+ Chargers |
| MAX1926ETC | Switch-Mode 1-Cell Li+ Chargers |
| MAX1925ETC | Switch-Mode 1-Cell Li+ Chargers |
| MAX192AMJP | Low-Power, 8-Channel, Serial 10-Bit ADC |
| MAX192AEAP | Low-Power, 8-Channel, Serial 10-Bit ADC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1925ETC | 功能描述:电池管理 Switch-Mode 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1925ETC+ | 功能描述:电池管理 Switch-Mode 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1925ETC+T | 功能描述:电池管理 Switch-Mode 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1925ETC-T | 功能描述:电池管理 Switch-Mode 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1926ETC | 功能描述:电池管理 Switch-Mode 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。