- 您现在的位置：买卖IC网 > PDF目录383342 > MAX194BCWE (MAXIM INTEGRATED PRODUCTS INC) 14-Bit, 85ksps ADC with 10A Shutdown PDF资料下载
参数资料
| 型号： | MAX194BCWE |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | ADC |
| 英文描述： | 14-Bit, 85ksps ADC with 10A Shutdown |
| 中文描述： | 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封装： | SO-16 |
| 文件页数： | 8/24页 |
| 文件大小： | 223K |
| 代理商： | MAX194BCWE |
M
sion and
EOC
will go high on the following CLK falling
edge (Figure 4).
CONV
is ignored during conversions.
External Clock
The conversion clock (CLK) should have a duty cycle
between 25% and 75% at 1.7MHz (the maximum clock
frequency). For lower frequency clocks, ensure the
minimum high and low times exceed 150ns. The mini-
mum clock rate for accurate conversion is 125Hz for
temperatures up to +70°C or 1kHz at +125°C due to
leakage of the sampling capacitor array. In addition,
CLK should not remain high longer than 50ms at tem-
peratures up to +70°C or 500μs at +125°C. If CLK is
held high longer than this,
RESET
must be pulsed low
to initiate a recalibration because it is possible that
state information stored in internal dynamic memory
may be lost. The MAX194’s clock can be stopped
indefinitely if it is held low.
If the frequency, duty cycle, or other aspects of the
clock signal’s shape change, the offset created by cou-
pling between CLK and the analog inputs (AIN and
REF) changes. Recalibration corrects for this offset and
restores DC accuracy.
Output Data
The conversion result is clocked out MSB first, format-
ted as 14 data bits plus two sub-LSBs. Serial data is
available on DOUT only when
CS
is held low.
Otherwise, DOUT is in a high-impedance state. There
are two ways to read the data on DOUT. To read the
data bits as they are determined (at the CLK clock
rate), hold
CS
low during the conversion. To read
results between conversions, hold
CS
low and clock
SCLK at up to 5MHz.
If you read the serial data bits as they are determined
(at the conversion-clock rate),
EOC
frames the data bits
(Figure 6). Conversion begins with the first falling CLK
edge, after
CONV
goes low and the input signal has
been acquired. Data bits are shifted out of DOUT on
subsequent falling CLK edges. Clock data in on CLK’s
rising edge or, if the clock speed is greater than 1MHz,
on the following falling edge of CLK to meet the maxi-
mum CLK-to-DOUT timing specification. See the
Operating Modes and SPI/QSPI Interfaces section
for additional information. Reading the serial data dur-
ing the conversion results in the maximum conversion
throughput, because a new conversion can begin
immediately after the input acquisition period following
the previous conversion.
14-Bit, 85ksps ADC with 10μA S hutdown
8
_______________________________________________________________________________________
TRACK/HOLD
CLK
CONVERSION
BEGINS
CONVERSION
ENDS
t
AQ
*
*
THE FALLING EDGE OF CONV MUST OCCUR IN THIS REGION
t
CEL
t
CW
t
CEH
t
CC2
t
CC1
EOC
CONV
Figure 4. Initiating Conversions—Less than 3 CLK cycles since end of previous conversion.
SPI/QSPI are trademarks of Motorola Corp.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX194BCPE | 14-Bit, 85ksps ADC with 10A Shutdown |
| MAX194ACWE | 14-Bit, 85ksps ADC with 10A Shutdown |
| MAX194AEPE | Fixed-Point Digital Signal Processor 532-FCBGA |
| MAX194AMDE | 14-Bit, 85ksps ADC with 10A Shutdown |
| MAX194BEPE | Fixed-Point Digital Signal Processor 532-FCBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX194BCWE+ | 功能描述:模数转换器 - ADC 14Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194BCWE+T | 功能描述:模数转换器 - ADC 14Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194BCWE-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194BEPE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX194BEPE+ | 功能描述:模数转换器 - ADC 14Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。