- 您现在的位置：买卖IC网 > PDF目录1841 > MAX1954AEUB+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 10-UMAX PDF资料下载
参数资料
| 型号： | MAX1954AEUB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/18页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 360kHz |
| 占空比： | 93% |
| 电源电压： | 3 V ~ 13.2 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
Low-Cost, Current-Mode PWM Buck
Controller with Foldback Current Limit
where V IN is the input voltage and f S is the switching
frequency. Choose a R SNUB power rating that meets
the specific application’s derating rule for the power
dissipation calculated.
Input Capacitor
The input filter capacitor reduces peak currents drawn
from the power source and reduces noise and voltage
ripple on the input caused by the circuit’s switching.
The input capacitor must meet the ripple current
requirement (I RMS ) imposed by the switching currents
defined by the following equation:
where I P-P is the peak-to-peak inductor current (see the
Inductor Value section). These equations are suitable
for initial capacitor selection, but final values should be
chosen based on a prototype or evaluation circuit. As a
general rule, a smaller current ripple results in less out-
put voltage ripple. Since the inductor ripple current is a
factor of the inductor value and input voltage, the out-
put voltage ripple decreases with larger inductance,
and increases with higher input voltages. For the
MAX1954A polymer, tantalum, or aluminum electrolytic
capacitors are recommended. Lower-cost aluminum
electrolytic capacitors with relatively low ESR are avail-
(
I RMS =
I LOAD ×
V OUT × V IN ? V OUT
V IN
)
able and can be used for the MAX1954A, if the larger
physical size is acceptable. For reliable and safe oper-
ation, ensure that the capacitor’s voltage and ripple-
current ratings exceed the calculated values.
The devices’ response to a load transient depends on
V RIPPLE ( C ) =
V RIPPLE ( ESL ) = ? IN ? × ESL
I P ? P = ? IN OUT ? × ? OUT ?
I RMS has a maximum value when the input voltage
equals twice the output voltage (V IN = 2 x V OUT ); there-
fore, I RMS(MAX) = I LOAD / 2. Ceramic capacitors are
recommended due to their low equivalent series resis-
tance (ESR) and equivalent series inductance (ESL) at
high frequencies, and their relatively low cost. Choose
a capacitor that exhibits less than 10 ° C temperature
rise at the maximum operating root-mean-square (RMS)
current for optimum long-term reliability.
Output Capacitor
The key selection parameters for the output capacitor
are the actual capacitance value, ESR, ESL, and the
voltage-rating requirements. These parameters affect
the overall stability, output voltage ripple, and transient
response. The output ripple has three components: vari-
ations in the charge stored in the output capacitor, and
the voltage drop across the capacitor’s ESR and ESL
caused by the current into and out of the capacitor. The
equation below estimates the maximum ripple voltage:
V RIPPLE = V RIPPLE ( ESR ) + V RIPPLE ( C ) + V RIPPLE ( ESL )
The output voltage ripple as a consequence of the ESR,
output capacitance, and ESL are as follows:
V RIPPLE ( ESR ) = I P ? P × ESR
I P ? P
8 × C OUT × f S
? V ?
? L ?
? V ? V ? ? V ?
? f S × L ? ? V IN ?
the selected output capacitors. After a load transient,
the output voltage instantly changes by ESR x ? I LOAD .
Before the controller can respond, the output voltage
deviates further depending on the inductor and output
capacitor values. After a short period of time (see the
Typical Operating Characteristics ), the controller
responds by regulating the output voltage back to its
nominal state. The controller response time depends on
its closed-loop bandwidth. With a higher bandwidth, the
response time is faster, thus preventing the output volt-
age from deviating further from its regulation value.
Compensation Design
The MAX1954A uses an internal transconductance
error amplifier whose output compensates the control
loop. The external inductor, high-side MOSFET, output
capacitor, compensation resistor, and compensation
capacitors determine the loop stability. The inductor
and output capacitors are chosen based on perfor-
mance, size, and cost. Additionally, the compensation
resistor and capacitors are selected to optimize control-
loop stability. The component values in Figures 1 and 2
yield stable operation over the given range of input-to-
output voltages and load currents. The controller uses a
current-mode control scheme that regulates the output
voltage by forcing the required current through the
external inductor. The MAX1954A uses the voltage
across the high-side MOSFET ’s on-resistance
(R DS(ON) ) to sense the inductor current. Current-mode
control eliminates the double pole in the feedback loop
caused by the inductor and output capacitor, resulting
in a smaller phase shift and requiring less elaborate
error-amplifier compensation. A single-series compen-
sation resistor (R C ) and compensation capacitor (C C ) is
all that is needed to have a stable high-bandwidth loop
in applications where ceramic capacitors are used for
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1954EUB+ | IC REG CTRLR BUCK PWM CM 10-UMAX |
| MAX1956ETI+T | IC REG CTRLR BUCK PWM VM 28-TQFN |
| MAX1961EEP+ | IC REG CTRLR BUCK PWM VM 20-QSOP |
| MAX1964TEEE+ | IC POWER CTRLR/SEQUENCER 16QSOP |
| MAX1967EUB+T | IC REG CTRLR BUCK PWM VM 10-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1954AEUB-TG05 | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1954AEUB-TG077 | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1954AEVKIT | 功能描述:电流型 PWM 控制器 Evaluation Kit for the MAX1954A RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1954BEUB | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1954BEUB+ | 功能描述:电流型 PWM 控制器 Current-Mode PWM Buck Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。