- 您现在的位置：买卖IC网 > PDF目录15489 > MAX1957EUB+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 10-UMAX PDF资料下载
参数资料
| 型号： | MAX1957EUB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 360kHz |
| 占空比： | 96% |
| 电源电压： | 3 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
Low-Cost, High-Frequency, Current-Mode PWM
Buck Controller
Current-Sense Amplifier
The MAX1953/MAX1954/MAX1957s’ current-sense cir-
cuit amplifies (A V = 3.5 typ) the current-sense voltage
(the high-side MOSFET’s on-resistance (R DS(ON) ) multi-
plied by the inductor current). This amplified current-
sense signal and the internal-slope compensation
signal are summed (V SUM ) together and fed into the
PWM comparator’s inverting input. The PWM compara-
tor shuts off the high-side MOSFET when V SUM
exceeds the integrated feedback voltage (V COMP ).
Current-Limit Circuit
The current-limit circuit employs a lossless current-limit-
ing algorithm that uses the low-side and high-side
MOSFETs’ on-resistances as the sensing elements. The
voltage across the high-side MOSFET is monitored for
current-mode feedback, as well as current limit. This
signal is amplified by the current-sense amplifier and is
compared with a current-sense voltage. If the current-
sense signal is larger than the set current-limit voltage,
the high-side MOSFET turns off. Once the high-side
MOSFET turns off, the low-side MOSFET is monitored
for current limit. If the voltage across the low-side MOS-
FET (R DS(ON) ? I INDUCTOR ) does not exceed the short-
circuit current limit, the high-side MOSFET turns on
normally. In this condition, the output drops smoothly
out of regulation. If the voltage across the low-side
MOSFET exceeds the short-circuit current-limit thresh-
old at the beginning of each new oscillator cycle, the
MAX1953/MAX1954/MAX1957 do not turn on the high-
side MOSFET.
In the case where the output is shorted, the low-side
MOSFET is monitored for current limit. The low-side
MOSFET is held on to let the current in the inductor
ramp down. Once the voltage across the low-side
MOSFET drops below the short-circuit current-limit
threshold, the high-side MOSFET is pulsed. Under this
condition, the frequency of the MAX1953/MAX1954/
MAX1957 appears to decrease because the on-time of
the low-side MOSFET extends beyond a clock cycle.
The actual peak output current is greater than the
short-circuit current-limit threshold by an amount equal
to the inductor ripple current. Therefore, the exact cur-
rent-limit characteristic and maximum load capability
are a function of the low-side MOSFET on-resistance,
inductor value, input voltage, and output voltage.
The short-circuit current-limit threshold is preset for the
MAX1954/MAX1957 at 210mV. The MAX1953, however,
has three options for the current-limit threshold: con-
nect ILIM to IN for a 320mV threshold, connect ILIM to
GND for 105mV, or leave floating for 210mV.
Synchronous Rectifier Driver (DL)
Synchronous rectification reduces conduction losses in
the rectifier by replacing the normal Schottky catch
diode with a low-resistance MOSFET switch. The
MAX1953/MAX1954/MAX1957 use the synchronous
rectifier to ensure proper startup of the boost gate-
driver circuit and to provide the current-limit signal. The
DL low-side waveform is always the complement of the
DH high-side drive waveform. A dead-time circuit moni-
tors the DL output and prevents the high-side MOSFET
from turning on until DL is fully off, thus preventing
cross-conduction or shoot-through. In order for the
dead-time circuit to work properly, there must be a low-
resistance, low-inductance path from the DL driver to
the MOSFET gate. Otherwise, the sense circuitry in the
MAX1953/MAX1954/MAX1957 can interpret the MOS-
FET gate as OFF when gate charge actually remains.
The dead time at the other edge (DH turning off) is
determined through gate sensing as well.
High-Side Gate-Drive Supply (BST)
Gate-drive voltage for the high-side switch is generated
by a flying capacitor boost circuit (Figure 5). The
capacitor between BST and LX is charged from the V IN
supply up to V IN , minus the diode drop while the low-
side MOSFET is on. When the low-side MOSFET is
switched off, the stored voltage of the capacitor is
stacked above LX to provide the necessary turn-on
voltage (V GS ) for the high-side MOSFET. The controller
then closes an internal switch between BST and DH to
turn the high-side MOSFET on.
Undervoltage Lockout
If the supply voltage at IN drops below 2.75V, the
MAX1953/MAX1954/MAX1957 assume that the supply
voltage is too low to make valid decisions, so the UVLO
circuitry inhibits switching and forces the DL and DH
gate drivers low. After the voltage at IN rises above
2.8V, the controller goes into the startup sequence and
resumes normal operation.
Startup
The MAX1953/MAX1954/MAX1957 start switching when
the voltage at IN rises above the UVLO threshold.
However, the controller is not enabled unless all four of
the following conditions are met:
? V IN exceeds the 2.8V UVLO threshold.
? The internal reference voltage exceeds 92% of its
nominal value (V REF > 1 V).
? The internal bias circuitry powers up.
? The thermal overload limit is not exceeded.
14
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J1Y-EX-B1 | CONVERTER MOD DC/DC 3.3V 49.5W |
| UPJ1H471MHD | CAP ALUM 470UF 50V 20% RADIAL |
| MAX8545EUB+ | IC REG CTRLR BUCK PWM VM 10-UMAX |
| VI-J1Y-EW-B1 | CONVERTER MOD DC/DC 3.3V 66W |
| URS0J472MHD | CAP ALUM 4700UF 6.3V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1957EUB+ | 功能描述:电流型 PWM 控制器 High-f Current-Mode PWM Buck Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1957EUB+T | 功能描述:电流型 PWM 控制器 High-f Current-Mode PWM Buck Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1957EUB-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX19586ETN | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX19586ETN+D | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。