- 您现在的位置：买卖IC网 > PDF目录9834 > MAX195BCWE+T (Maxim Integrated Products)IC ADC 16BIT 85KSPS 16-SOIC PDF资料下载
参数资料
| 型号： | MAX195BCWE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 85KSPS 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 位数： | 16 |
| 采样率（每秒）： | 85k |
| 数据接口： | QSPI?，串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 80mW |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页
_______________Detailed Description
The MAX195 uses a successive-approximation register
(SAR) to convert an analog input to a 16-bit digital
code, which outputs as a serial data stream. The data
bits can be read either during the conversion, at the
CLK clock rate, or between conversions asynchronous
with CLK at the SCLK rate (up to 5Mbps).
The MAX195 includes a capacitive digital-to-analog
converter (DAC) that provides an inherent track/hold
input. The interface and control logic are designed for
easy connection to most microprocessors (Ps), limiting
the need for external components. In addition to the
SAR and DAC, the MAX195 includes a serial interface, a
sampling comparator used by the SAR, ten calibration
DACs, and control logic for calibration and conversion.
The DAC consists of an array of 16 capacitors with
binary weighted values plus one “dummy LSB” capaci-
tor (Figure 1). During input acquisition in unipolar
mode, the array’s common terminal is connected to
AGND and all free terminals are connected to the input
signal (AIN). After acquisition, the common terminal is
disconnected from AGND and the free terminals are
disconnected from AIN, trapping a charge proportional
to the input voltage on the capacitor array.
The free terminal of the MSB (largest) capacitor is con-
nected to the reference (REF), which pulls the common
terminal (connected to the comparator) positive.
Simultaneously, the free terminals of all other capaci-
tors in the array are connected to AGND, which drives
the comparator input negative. If the analog input is
near VREF, connecting the MSB’s free terminal to REF
only pulls the comparator input slightly positive.
However, connecting the remaining capacitor’s free ter-
minals to ground drives the comparator input well
below ground, so the comparator input is negative, the
comparator output is low, and the MSB is set high. If
the analog input is near ground, the comparator output
is high and the MSB is low.
Following this, the next largest capacitor is disconnect-
ed from AGND and connected to REF, and the com-
parator determines the next bit. This continues until all
bits have been determined. For a bipolar input range,
the MSB capacitor is connected to REF rather than AIN
during input acquisition, which results in an input range
of VREF to -VREF.
MAX195
16-Bit, 85ksps ADC with 10A Shutdown
_______________________________________________________________________________________
5
______________________________________________________________Pin Description
PIN
NAME
FUNCTION
1
BP/UP/SHDN
Bipolar/Unipolar/Shutdown Input. Three-state input selects bipolar or unipolar input range, or shutdown.
0V = shutdown, +5V = unipolar, floating = bipolar.
2
CLK
Conversion Clock Input
3
SCLK
Serial Clock Input is used to shift data out between conversions. May be asynchronous to CLK.
4
VDDD
+5V Digital Power Supply
5
DOUT
Serial Data Output, MSB first
6
DGND
Digital Ground
7
EOC
End-of-Conversion/Calibration Output—normally low. Rises one clock cycle after the beginning of conversion
or calibration and falls one clock cycle after the end of either. May be used as an output framing signal.
8
CS
Chip-Select Input—active low. Enables the serial interface and the three-state data output (DOUT).
9
CONV
Convert-Start Input—active low. Conversion begins on the falling edge after CONV goes low if the input
signal has been acquired; otherwise, on the falling clock edge after acquisition.
10
RESET
Reset Input. Pulling RESET low places the ADC in an inactive state. Rising edge resets control logic and
begins calibration.
11
VSSD
-5V Digital Power Supply
12
REF
Reference Input, 0 to 5V
13
AIN
Analog Input, 0 to VREF unipolar or ±VREF bipolar range
14
AGND
Analog Ground
15
VSSA
-5V Analog Power Supply
16
VDDA
+5V Analog Power Supply
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3043ESE+T | IC RS485/422 TRANS QUAD 16-SOIC |
| MAX3041ESE+T | IC RS485/422 TRANS QUAD 16-SOIC |
| MAX122BCNG+ | IC ADC 12BIT 333KSPS 24-DIP |
| MAX3041EUE+T | IC RS485/422 TRANS QUAD 16TSSOP |
| MAX3044ESE+T | IC RS485/422 TRANS QUAD 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX195BEPE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BEPE+ | 功能描述:模数转换器 - ADC 16-Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BEPE+T | 制造商:Maxim Integrated Products 功能描述:16-BIT, 85KSPS ADC WITH 10?A SHUTDOWN - Tape and Reel |
| MAX195BEWE | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX195BEWE+ | 功能描述:模数转换器 - ADC 16-Bit 85ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。