- 您现在的位置：买卖IC网 > PDF目录383342 > MAX196BEAI (MAXIM INTEGRATED PRODUCTS INC) CONNECTOR PDF资料下载
参数资料
| 型号： | MAX196BEAI |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | CONNECTOR |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封装： | 0.200 INCH, 0.65 MM PITCH, SSOP-28 |
| 文件页数： | 13/16页 |
| 文件大小： | 165K |
| 代理商： | MAX196BEAI |
__________Applic ations Information
Power-On Reset
At power-up, the internal power-on reset circuitry sets
INT high and puts the device in normal operation/exter-
nal clock mode. This state is selected to keep the inter-
nal clock from loading the external clock driver when
the part is used in external clock mode.
Internal or External Referenc e
The MAX196/MAX198 can operate with either an inter-
nal or external reference. An external reference can be
connected to either the REF pin or the REFADJ pin
(Figure 9).
To use the REF input directly, disable the internal buffer
by tying REFADJ to V
DD
. Using the REFADJ input elimi-
nates the need to buffer the reference externally. When
the reference is applied at REFADJ , bypass REFADJ with
a 0.01μF capacitor to AGND.
The REFADJ internal buffer gain is trimmed to 1.6384 to
provide 4.096V at the REF pin from a 2.5V reference.
Internal Reference
The internally trimmed 2.50V reference is gained
through the REFADJ buffer to provide 4.096V at REF.
Bypass the REF pin with a 4.7μF capacitor to AGND
and the REFADJ pin with a 0.01μF capacitor to AGND.
The internal reference voltage is adjustable to ±1.5%
(±65 LSBs) with the reference-adjust circuit of Figure 1.
External Reference
At REF and REFADJ , the input impedance is a mini-
mum of 10k
for DC currents. During conversions, an
external reference at REF must be able to deliver
400μA DC load currents, and must have an output
impedance of 10
or less. If the reference has higher
output impedance or is noisy, bypass it close to the
REF pin with a 4.7μF capacitor to AGND.
With an external reference voltage of less than 4.096V
at the REF pin or less than 2.5V at the REFADJ pin, the
increase in the ratio of the RMS noise to the LSB value
(FS / 4096) results in performance degradation (loss of
effective bits).
Power-Down Mode
To save power, you can put the converter into low-
current shutdown mode between conversions. Two
programmable power-down modes are available:
STBYPD and FULLPD. Select STBYPD or FULLPD by
programming PD0 and PD1 in the input control byte.
When power-down is asserted, it becomes effective
only after the end of conversion. In all power-down
modes, the interface remains active and conversion
M
Multirange, S ingle +5V, 12-Bit DAS
with 12-Bit Bus Interfac e
______________________________________________________________________________________
13
REF
10k
2.5V
26
4.096V
4.7
μ
F
C
REF
0.01
μ
F
25
REFADJ
A
V
= 1.638
MAX196
MAX198
Figure 9a. Internal Reference
REF
10k
2.5V
26
4.7
μ
F
C
REF
2.5V
25
REFADJ
A
V
= 1.638
0.01
μ
F
MAX196
MAX198
4.096V
Figure 9c. The external reference overdrives the internal refer-
ence.
REF
V
DD
10k
2.5V
26
4.096V
4.7
μ
F
C
REF
25
REFADJ
A
V
= 1.638
MAX196
MAX198
Figure 9b. External Reference, Reference at REF
相关PDF资料 |
PDF描述 |
|---|---|
| MAX196BMYI | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
| MAX198BMYI | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
| MAX1961EEP | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
| MAX1960 | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
| MAX1960EEP | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX196BEAI+ | 功能描述:模数转换器 - ADC 12-Bit 6Ch 100ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX196BEAI+T | 功能描述:模数转换器 - ADC 12-Bit 6Ch 100ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX196BEAI-T | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX196BENI | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX196BENI+ | 功能描述:模数转换器 - ADC 12-Bit 6Ch 100ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。