- 您现在的位置：买卖IC网 > PDF目录5176 > MAX1982EUT+T (Maxim Integrated Products)IC REG LDO 1.2V .3A SOT23-6 PDF资料下载
参数资料
| 型号： | MAX1982EUT+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.2V .3A SOT23-6 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.2V |
| 输入电压： | 1.25 V ~ 5.5 V |
| 稳压器数量： | 1 |
| 电流 - 输出： | 300mA |
| 电流 - 限制（最小）： | 330mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 标准包装 |
| 产品目录页面： | 1410 (CN2011-ZH PDF) |
| 其它名称： | MAX1982EUT+TDKR |
Low-Voltage, Low-Dropout Linear Regulators
with External Bias Supply
350
300
250
200
150
100
50
MAXIMUM CONTINUOUS CURRENT
T A = +25 ° C
T A = +50 ° C
T A = +70 ° C
T J = +150 ° C
The MAX1982/MAX1983 load-transient response graphs
(see the Typical Operating Characteristics) show two
components of the output response: a DC shift from the
output impedance due to the load current change and
the transient response. A typical transient response for a
step change in the load current from 1mA to 300mA is
20mV. Increasing the output capacitor ’s value and
decreasing the ESR attenuate the overshoot.
Input/Output (Dropout) Voltage
A regulator’s minimum input-to-output voltage differen-
tial (dropout voltage) determines the lowest usable sup-
ply voltage. In battery-powered systems, the dropout
0
0 1 2 3 4 5
INPUT-OUTPUT DIFFERENTIAL VOLTAGE (V)
Figure 5. Power Operating Region—Maximum Output Current
vs. Supply Voltage
only. The UVLO threshold is 4.2V, and V BIAS must
remain above this level for proper operation, regardless
of the level of V IN .
Input Capacitor
Bypass IN to ground with a 10μF or greater ceramic
capacitor. Bypass BIAS to ground with a 0.1μF ceramic
capacitor for normal operation in most applications.
Output Capacitor
Bypass OUT to ground with a low-ESR ceramic capaci-
tor greater than 10μF. The ESR must be less than
35m Ω . Choose an output capacitor to maintain the
required output voltage tolerance during a load step.
The change in output voltage is,
voltage determines the useful end-of-life battery volt-
age. Because the MAX1982/MAX1983 use an N-chan-
nel pass transistor, the dropout voltage is a function of
the drain-to-source on-resistance (R DS(ON) = 1 Ω max)
multiplied by the load current (see the Typical
Operating Characteristics):
V DROPOUT = V IN ? V OUT = R DS ( ON ) × I OUT
PC Board Layout Guidelines
The MAX1982/MAX1983 require proper layout to
achieve the intended output power level, high efficiency,
and low noise. Proper layout involves the use of a
ground plane, appropriate component placement, and
correct routing of traces using appropriate trace widths.
1) Minimize high-current ground loops. Connect the
ground of the device, the input capacitor, and the
output capacitor together at one point.
2) To optimize performance, a ground plane is essen-
tial. Use all available copper layers in applications
Δ t
?
Δ V = I ? ESR +
? ?
?
?
C OUT ? ?
where the device is located on a multilayer board.
3) Connect the input filter capacitor less than 10mm
from IN. The connecting copper trace carries large
where I is the load current, C OUT is the output capaci-
tance, and Δ t is the duration of the load step.
Noise, PSRR, and Transient Response
The MAX1982/MAX1983 operate with low-dropout volt-
age and low quiescent current in notebook computers
while maintaining good noise, transient response, and
AC rejection specifications. See the Typical Operating
Characteristics for a graph of Power-Supply Rejection
Ratio (PSRR) vs. Frequency. Improved supply-noise
rejection and transient response can be achieved by
increasing the values of the input and output capacitors
and use passive filtering techniques when operating
from noisy sources.
currents and must be at least 2mm wide, preferably
5mm wide.
4) Use as much copper as necessary to increase the
thermal resistance of the device. In general, more
copper provides better heatsinking capabilities.
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| RCM18DRYF | CONN EDGECARD 36POS DIP .156 SLD |
| 2256-27L | POWER CHOKE 150UH MOLDED AXIAL |
| MIC5319-2.9YML TR | IC REG LDO 2.9V .5A 6-MLF |
| SN101M6R3ST | CAP ALUM 100UF 6.3V 20% RADIAL |
| GMA31DTKI | CONN EDGECARD 62POS DIP .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1982EVKIT | 功能描述:低压差稳压器 - LDO Evaluation Kit for the MAX1982 MAX1983 RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX1983EUT | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE, LOW-DROPOUT LINEAR REGULATORS WI - Bulk 制造商:Rochester Electronics LLC 功能描述: |
| MAX1983EUT+ | 制造商:Maxim Integrated Products 功能描述:LDO REG 0.8V TO 2V 0.3A 6PIN SOT-23 - Rail/Tube |
| MAX1983EUT+T | 功能描述:低压差稳压器 - LDO Low-Voltage w/ External Bias Supply RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX1983EUT-T | 功能描述:低压差稳压器 - LDO RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。