- 您现在的位置：买卖IC网 > PDF目录19339 > MAX1989MEE+T (Maxim Integrated)IC TEMP SENSOR REMOTE 16-QSOP PDF资料下载
参数资料
| 型号： | MAX1989MEE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/17页 |
| 文件大小： | 497K |
| 描述： | IC TEMP SENSOR REMOTE 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部和外部 |
| 感应温度： | -55°C ~ 125°C，外部传感器 |
| 精确度： | ±3.5°C 本地（最大），±5°C 远程（最大） |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
Diode Fault Alarm
There is a continuity fault detector at DXP_ that detects
whether the remote diode has an open-circuit condi-
tion. At the beginning of each conversion, the diode
fault is checked, and the status byte is updated. This
fault detector is a simple voltage detector; if DXP_ rises
above V
CC
- 1V (typ) due to the diode current source, a
fault is detected. Note that the diode fault is not
checked until a conversion is initiated, so immediately
after power-on reset, the status byte indicates no fault
is present, even if the diode path is broken.
If any remote channel is shorted (DXP_ to DXN_ or
DXP_ to GND), the ADC reads 0000 0000 so as not to
trip either the T
HIGH
or T
LOW
alarms at their POR set-
tings. In applications that are never subjected to 0癈 in
normal operation, a 0000 0000 result can be checked
to indicate a fault condition in which DXP_ is acciden-
tally short circuited. Similarly, if DXP_ is short circuited
to V
CC
, the ADC reads +127癈 for all remote and local
channels, and the device alarms.
AALLEERRTT Interrupts
The ALERT interrupt output signal is latched and can
only be cleared by reading the alert response address.
Interrupts are generated in response to T
HIGH
and T
LOW
comparisons and when a remote diode is disconnected
(for continuity fault detection). The interrupt does not halt
automatic conversions; new temperature data continues
to be available over the SMBus interface after ALERT is
asserted. The interrupt output pin is open drain so that
devices can share a common interrupt line. The interrupt
rate can never exceed the conversion rate.
The interface responds to the SMBus alert response
address, an interrupt pointer return-address feature
(see Alert Response Address section). Prior to taking
corrective action, always check to ensure that an inter-
rupt is valid by reading the current temperature.
Alert Response Address
The SMBus alert response interrupt pointer provides
quick fault identification for simple slave devices that
lack the complex, expensive logic needed to be a bus
master. Upon receiving an ALERT interrupt signal, the
host master can broadcast a receive byte transmission
to the alert response slave address (0001 100). Then
any slave device that generated an interrupt attempts
to identify itself by putting its own address on the bus
(Table 3).
The alert response can activate several different slave
devices simultaneously, similar to the I
2
C general call. If
more than one slave attempts to respond, bus arbitra-
tion rules apply, and the device with the lower address
code wins. The losing device does not generate an
acknowledge and continues to hold the ALERT line low
until serviced (implies that the host interrupt input is
Multichannel Remote/Local
Temperature Sensors
______________________________________________________________________________________ 11
Table 2. Data Format (Twos Complement)
Table 3. Read Format for Alert Response
Address (0001100)
ADD6
6
Provide the current
MAX1668/MAX1805/MAX1989
slave address that was latched at
POR (Table 8)
FUNCTION
ADD5
5
ADD4
4
ADD3
3
ADD2
2
ADD1
1
ADD7
7
(MSB)
1
0
(LSB)
Logic 1
BIT
NAME
DIGITAL OUTPUT DATA BITS
TEMP
(癈)
ROUNDED
TEMP
(癈)
SIGN
MSB
LSB
+130.00
+127
0
111
1111
+127.00
+127
0
111
1111
+126.50
+127
0
111
1111
+126.00
+126
0
111
1110
+25.25
+25
0
001
1001
+0.50
+1
0
000
0000
+0.25
+0
0
000
0000
+0.00
+0
0
000
0000
-0.25
+0
0
000
0000
-0.50
+0
0
000
0000
-0.75
-1
1
111
1111
-1.00
-1
1
111
1111
-25.00
-25
1
110
0111
-25.50
-25
1
110
0110
-54.75
-55
1
100
1001
-55.00
-55
1
100
1001
-65.00
-65
1
011
1111
-70.00
-65
1
011
1111
相关PDF资料 |
PDF描述 |
|---|---|
| VJ1206A390KBAAT4X | CAP CER 39PF 50V 10% NP0 1206 |
| GCM02DRKN-S13 | CONN EDGECARD 4POS .156 EXTENDER |
| VE-B3J-EU-S | CONVERTER MOD DC/DC 36V 200W |
| R05P23.3D/P/R6.4 | CONV DC/DC 2W 05VIN +/-3.3VOUT |
| VE-B3F-EU-S | CONVERTER MOD DC/DC 72V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1989MEE-TG11 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1989MUE | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1989MUE+ | 功能描述:板上安装温度传感器 MultiCh Remote Local Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1989MUE+T | 功能描述:板上安装温度传感器 MultiCh Remote Local Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1989MUE-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。