- 您现在的位置：买卖IC网 > PDF目录18734 > MAX19995ETX+ (Maxim Integrated)IC DOWNCONVERTER 2CH 36TQFN PDF资料下载
参数资料
| 型号： | MAX19995ETX+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 26/29页 |
| 文件大小： | 0K |
| 描述： | IC DOWNCONVERTER 2CH 36TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| RF 型： | CDMA，DCS，EDGE，GSM，UMTS，WCDMA |
| 频率： | 1.7GHz ~ 2.2GHz |
| 混频器数目： | 1 |
| 增益： | 9dB |
| 噪音数据： | 9dB |
| 次要属性： | 降频变频器 |
| 电流 - 电源： | 212mA，370mA |
| 电源电压： | 3 V ~ 3.6 V，4.75 V ~ 5.25 V |
| 包装： | 托盘 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页
Dual, SiGe, High-Linearity, 1700MHz to 2200MHz
Downconversion Mixer with LO Buffer/Switch
Differential IF
The MAX19995 has an IF frequency range of 50MHz to
500MHz, where the low-end/high-end frequency
depends on the frequency response of the external IF
components. Note that these differential ports are ideal
for providing enhanced IIP2 performance. Single-
ended IF applications require a 4:1 (impedance ratio)
balun to transform the 200 Ω differential IF impedance
to a 50 Ω single-ended system. After the balun, the
return loss is typically 12.5dB. The user can use a dif-
ferential IF amplifier on the mixer IF ports, but a DC
block is required on both IFD+/IFD- and IFM+/IFM-
ports to keep external DC from entering the IF ports of
the mixer.
Applications Information
Input and Output Matching
The RF and LO inputs are internally matched to 50 Ω .
No matching components are required. The RF port
input return loss is typically better than 16dB over the
RF frequency range of 1700MHz to 2200MHz and
return loss at the LO ports are typically better than
16dB over the entire LO range. RF and LO inputs
require only DC-blocking capacitors for interfacing.
The IF output impedance is 200 Ω (differential). For
evaluation, an external low-loss 4:1 (impedance ratio)
balun transforms this impedance to a 50 Ω single-ended
output (see the Typical Application Circuit).
Reduced-Power Mode
Each channel of the MAX19995 has two pins
(LO_ADJ_ _, IF_ _SET) that allow external resistors to
set the internal bias currents. Nominal values for these
resistors are given in Table 1. Larger value resistors
can be used to reduce power dissipation at the
expense of some performance loss. See the Typical
Operating Characteristics to evaluate the biasing vs.
performance tradeoff. If ±1% resistors are not readily
available, ±5% resistors may be substituted.
Significant reductions in power consumption can also be
realized by operating the mixer with an optional supply
voltage of +3.3V. Doing so reduces the overall power
consumption by up to 62%. See the +3.3V Supply AC
Electrical Characteristics and the relevant +3.3V curves
in the Typical Operating Characteristics section.
IND_EXT_ Inductors
For applications requiring optimum RF-to-IF and LO-to-
IF isolation, connect low-ESR inductors from IND_EXT_
(pins 15 and 31) to ground. When improved isolation is
not required, connect IND_EXT_ to ground using a 0 Ω
resistance. See the Typical Operating Characteristics to
evaluate the isolation vs. inductor value tradeoff.
Layout Considerations
A properly designed PCB is an essential part of any
RF/microwave circuit. Keep RF signal lines as short as
possible to reduce losses, radiation, and inductance.
The load impedance presented to the mixer must be
such that any capacitance from both IF- and IF+ to
ground does not exceed several picofarads. For the
best performance, route the ground pin traces directly
to the exposed pad under the package. The PCB
exposed pad MUST be connected to the ground plane
of the PCB. It is suggested that multiple vias be used to
connect this pad to the lower-level ground planes. This
method provides a good RF/thermal-conduction path for
the device. Solder the exposed pad on the bottom of the
device package to the PCB. The MAX19995 evaluation
kit can be used as a reference for board layout. Gerber
files are available upon request at www.maxim-ic.com .
Power-Supply Bypassing
Proper voltage-supply bypassing is essential for high-
frequency circuit stability. Bypass each V CC pin and
TAPMAIN/TAPDIV with the capacitors shown in the
Typical Application Circuit (see Table 1 for component
values). Place the TAPMAIN/TAPDIV bypass capacitors
to ground within 100 mils of the pin.
Exposed Pad RF/Thermal Considerations
The exposed pad (EP) of the MAX19995’s 36-pin thin
QFN-EP package provides a low thermal-resistance
path to the die. It is important that the PCB on which the
MAX19995 is mounted be designed to conduct heat
from the EP. In addition, provide the EP with a low-
inductance path to electrical ground. The EP MUST be
soldered to a ground plane on the PCB, either directly
or through an array of plated via holes.
26
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| DP1283C868 | MODULE DROP IN FOR XE1283 868MHZ |
| MAX2681EUT+T | IC SIGE DOWNCONV MIXER SOT23-6 |
| DP1283C433 | MODULE DROP IN FOR XE1283 433MHZ |
| CSX750FCC18.432M-UT | OSCILLATOR 18.4320 MHZ SMD |
| 636L3C001M54400 | OSCILLATOR 1.544 MHZ 3.3V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX19995ETX+ | 功能描述:上下转换器 High-Gain 1.7GHz to 2.2GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX19995ETX+T | 功能描述:上下转换器 High-Gain 1.7GHz to 2.2GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX19995EVKIT# | 功能描述:射频开发工具 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX19996AETP+ | 功能描述:上下转换器 High-Gain 2GHz to 3.9GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
| MAX19996AETP+T | 功能描述:上下转换器 High-Gain 2GHz to 3.9GHz Downconv RoHS:否 制造商:Texas Instruments 产品:Down Converters 射频:52 MHz to 78 MHz 中频:300 MHz LO频率: 功率增益: P1dB: 工作电源电压:1.8 V, 3.3 V 工作电源电流:120 mA 最大功率耗散:1 W 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PQFP-128 |
发布紧急采购，3分钟左右您将得到回复。