- 您现在的位置：买卖IC网 > PDF目录383344 > MAX2034CTM (MAXIM INTEGRATED PRODUCTS INC) Quad-Channel, Ultra-Low-Noise Amplifier with Digitally Programmable Input Impedance PDF资料下载
参数资料
| 型号： | MAX2034CTM |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | Quad-Channel, Ultra-Low-Noise Amplifier with Digitally Programmable Input Impedance |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, QCC48 |
| 封装： | 7 X 7 MM, 0.80 MM HEIGHT, MO-220, TQFN-48 |
| 文件页数： | 9/13页 |
| 文件大小： | 356K |
| 代理商： | MAX2034CTM |
Integrated Input Damping Capacitor
At high frequencies, gain peaking can occur due to an
active input termination becoming less effective when
the gain rolls off. Although an external shunting capaci-
tor can be used to mitigate this effect, different input
impedance modes require different capacitor values.
The MAX2034 integrates a damping capacitor for each
of the four programmed input impedance modes. When
the input impedance is programmed by applying the
appropriate D2/D1/D0, an optimal capacitor value is
also chosen for the particular input impedance mode,
eliminating the need for external capacitors.
Overload Recovery
The device is also optimized for quick overload recov-
ery for operation under the large input signal conditions
that are typically found in ultrasound input-buffer imag-
ing applications. Internal signal clipping is symmetrical.
Input overloads can be prevented with the input-clamp-
ing diodes. See the
Typical Operating Characteristics
that illustrate the rapid recovery time from a transmit-
related overload.
Sleep Mode
The sleep mode function allows the MAX2034 to be
configured in a low-power state when the amplifiers are
not being used. In sleep mode, all amplifiers are pow-
ered down, the total supply current of the device
reduces to 0.8mA, and the input impedance of each
amplifier is set at high impedance. Drive the PD input
high to activate sleep mode. For normal operation,
drive the PD input low.
Applications Information
Analog Input Coupling
AC-couple to ground the analog bypass input by con-
necting a 0.1μF capacitor at the INB1–INB4 input to
GND (0.1μF recommended). Since the amplifiers are
designed with a differential input stage, bypassing the
INB1–INB4 inputs configures the MAX2034 for single-
ended inputs at IN1–IN4.
Connect the IN1–IN4 inputs to their source circuits
through 0.1μF series capacitors. Connect the feedback
ports ZF1–ZF4 to the source circuits through 0.018μF
capacitors. (These capacitors will be 1/(5.5) as large as
the input-coupling capacitors. This equalizes the high-
pass filter characteristic of both the input and feedback
input ports, due to the feedback resistance related by a
factor of 1/(5.5) to the input impedance.)
Note that the active input circuitry of the MAX2034 is
stable, and does not require external ferrite beads or
shunt capacitors to achieve high-frequency stability.
The
Typical Application Circuit
illustrates these cou-
pling capacitors. If a ground-referenced current-limiting
stage precedes the MAX2034 inputs, its output can be
connected to the integrated clamping diodes on pins
INC1–INC4 to facilitate very rapid recovery from tran-
sient overloads associated with transmitter operation in
ultrasound applications.
Analog Output Coupling
The differential outputs of the MAX2034 are capable of
driving a differential load impedance of 200
or
greater. The differential output has a common-mode
bias of approximately 2.45V. AC-couple these differen-
tial outputs if the next stage has a different common-
mode input range.
Board Layout
The pin configuration of the MAX2034 is optimized to
facilitate a very compact physical layout of the device
and its associated discrete components. A typical
application for this device might incorporate several
devices in close proximity to handle multiple channels
of signal processing.
The exposed paddle (EP) of the MAX2034’s thin QFN-
EP package provides a low thermal-resistance path to
the die. It is important that the PC board on which the
MAX2034 is mounted be designed to conduct heat
from the EP. In addition, provide the EP with a low-
inductance path to electrical ground. The EP
MUST
be
soldered to a ground plane on the PC board, either
directly or through an array of plated via holes.
M
Quad-Channel, Ultra-Low-Noise Amplifier with
Digitally Programmable Input Impedance
_______________________________________________________________________________________
9
ULTRASOUND IMD3
-25dB
F1 - (F2 - F1)
F1
F2
F2 + (F2 - F1)
Figure 1. Ultrasound IMD3 Measurement Technique
相关PDF资料 |
PDF描述 |
|---|---|
| MAX2034CTM-T | Quad-Channel, Ultra-Low-Noise Amplifier with Digitally Programmable Input Impedance |
| MAX2039 | Evaluation Kit |
| MAX2039_1 | Evaluation Kit |
| MAX2039EVKIT | Evaluation Kit |
| MAX2043ETX | 1700MHz to 3000MHz High-Linearity, Low LO Leakage Base-Station Rx/Tx Mixer |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2034CTM+ | 功能描述:射频放大器 4Ch Amp w/Digital Prog Input Imp RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX2034CTM+T | 功能描述:射频放大器 4Ch Amp w/Digital Prog Input Imp RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX2034CTM-T | 功能描述:射频放大器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX2035 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Ultrasound Variable-Gain Amplifier |
| MAX2035_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Ultrasound Variable-Gain Amplifier |
发布紧急采购，3分钟左右您将得到回复。