- 您现在的位置：买卖IC网 > PDF目录18754 > MAX2043ETX+T (Maxim Integrated)IC BASE STATION HI LIN 36-TQFN PDF资料下载
参数资料
| 型号： | MAX2043ETX+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 12/17页 |
| 文件大小： | 0K |
| 描述： | IC BASE STATION HI LIN 36-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 频率： | 1.7GHz ~ 3GHz |
| P1dB： | 23dBm（199.5mW） |
| 噪音数据： | 7.8dB |
| RF 型： | UMTS，W-CDMA，DCS，PCS，CDMA2000，EDGE，PHS，WLL，WLAN，802.16/WiMax |
| 电源电压： | 4.75 V ~ 5.25 V |
| 电流 - 电源： | 108mA ~ 140mA |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
1700MHz to 3000MHz High-Linearity,
Low LO Leakage Base-Station Rx/Tx Mixer
Pin Description
PIN
1 – 5, 7, 10,
11, 12, 15,
18, 20, 22,
24, 25, 26,
28, 29,
31 – 36
6, 16, 21, 30
8
9
NAME
GND
V CC
RFTAP
RF
FUNCTION
These pins have no internal connection and can be left open or connected to ground. It is
suggested that these pins be grounded back to the exposed paddle where possible to improve pin-
to-pin isolation.
Power-Supply Connection. Connected to external power supply (5V). Bypass to GND with a 0.01μF
capacitor as close to the pin as possible.
Center Tap of the Internal RF Balun. Connected to internal RF balun center tap.
Single-Ended 50 ? RF Input/Output. DC grounded internally.
13, 14
IF+, IF- (ports) Differential IF Ports (50 ? ). 0V common-mode voltage.
17
19
23
27
EP
LO_ADJ
LO1
LOSEL
LO2
GND
Adjust LO Drive. A 360 ? ±1% resistor connected from this pin to ground sets the LO driver bias. A
1.1V DC voltage appears across this resistor.
Local Oscillator Input 1. Drive LOSEL high to select LO1.
Local Oscillator Select. Logic 0 selects LO2 and 1 selects LO1.
Local Oscillator Input 2. Drive LOSEL low to select LO2.
Exposed Paddle. Ground the exposed paddle using multiple ground vias.
Detailed Description
The MAX2043 can operate as either a downconverter
or an upconverter mixer that provides 7.5dB of conver-
sion loss with a typical 7.8dB noise figure. IIP3 is
+31dBm for both upconversion and downconversion.
The integrated baluns and matching circuitry allow for
50 ? single-ended interfaces to the RF port and two LO
ports. The RF port can be used as an input for down-
conversion or an output for upconversion. A single-
pole, double-throw (SPDT) switch provides 50ns
switching time between the two LO inputs with 43dB of
LO-to-LO isolation and -52dBm of LO leakage.
Furthermore, the integrated LO buffer provides a high
drive level to the mixer core, reducing the LO drive
required at the MAX2043 ’ s inputs to a -3dBm to +6dBm
range. The IF port incorporates a differential output for
downconversion, which is ideal for providing enhanced
IIP2 performance. For upconversion, the IF port is a dif-
ferential input.
Specifications are guaranteed over broad frequency
ranges to allow for use in UMTS/WCDMA and
2G/2.5G/3G DCS 1800, PCS 1900, cdma2000, and
WiMAX base stations. The MAX2043 is specified to
operate over a 1700MHz to 3000MHz RF input range, a
1900MHz to 3000MHz LO range, and an IF range of
near 0MHz to 350MHz. The external IF component sets
the lower frequency range.
RF Port and Balun
For using the MAX2043 as a downconverter, the RF
input is internally matched to 50 ? , requiring no external
matching components. A DC-blocking capacitor is
required because the input is internally DC shorted to
ground through the on-chip balun. The RF return loss is
typically 15dB over the entire 1700MHz to 3000MHz RF
frequency range. For upconverter operation, the RF
port is a single-ended output similarly matched to 50 ? .
An optional L-C BPF can be installed at the RF port to
improve some upconverter performance.
LO Inputs, Buffer, and Balun
The MAX2043 is optimized for a 1900MHz to 3000MHz
LO range. As an added feature, the MAX2043 includes
an internal LO SPDT switch that can be used for fre-
quency-hopping applications. The switch selects one
of the two single-ended LO ports, allowing the external
oscillator to settle on a particular frequency before it is
switched in. LO switching time is typically less than
50ns, which is more than adequate for typical GSM
applications. If frequency-hopping is not employed,
simply set the switch to either of the LO inputs. The
switch is controlled by a digital input (LOSEL): logic-
high selects LO1, logic-low selects LO2. LO1 and LO2
inputs are internally matched to 50 ? , requiring only a
22pF DC-blocking capacitor. To avoid damage to the
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| IF-6-24 | XFRMR 115/230V 12V 500MA 6VA PCB |
| MAX2067ETL+T | IC VGA PROG ANALOG 40TQFN-EP |
| 4112745 | GOLDCAREPLAN-GROUP2-4YR |
| IF-6-230 | XFRMR 115/230V 115V 50MA 6VA PCB |
| MAX2057ETX+T | IC AMP VARIABLE GAIN 36-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2043EVKIT | 功能描述:射频开发工具 RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX2044 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:SiGe, High-Linearity, 2300MHz to 4000MHz Upconversion/Downconversion Mixer with LO Buffer |
| MAX2044DEVBRD# | 功能描述:射频混合器 MAX2044 EVKIT RoHS:否 制造商:NXP Semiconductors 频率范围: 转换损失——最大: 工作电源电压:6 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| MAX2044ETP+ | 功能描述:射频混合器 2.3GHz-4GHz Up/Down Mixer RoHS:否 制造商:NXP Semiconductors 频率范围: 转换损失——最大: 工作电源电压:6 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| MAX2044ETP+T | 功能描述:射频混合器 2.3GHz-4GHz Up/Down Mixer RoHS:否 制造商:NXP Semiconductors 频率范围: 转换损失——最大: 工作电源电压:6 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。