参数资料
型号: MAX2117EVKIT+
厂商: Maxim Integrated
文件页数: 3/11页
文件大小: 0K
描述: KIT EVAL FOR MAX2117
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
类型: 调谐器
频率: 470MHz ~ 1GHz
适用于相关产品: MAX2117
已供物品:
MAX2117 Evaluation Kit
Component Suppliers
SUPPLIER
AMP/Tyco Electronics
Amphenol RF
AVX Corp.
Digi-Key Corp.
Emerson Network Power
Keystone Electronics Corp.
Maxim Integrated Products, Inc.
Murata Mfg. Co., Ltd.
Sullins Electronics Corp.
Texas instruments
PHONE
800-522-6752
800-627-7100
843-448-9411
800-344-4539
507-833-8822
209-796-2032
888-629-4642
770-436-1300
760-744-0125
800-336-5236
FAX
843-448-7139
218-681-3380
800-992-1884
770-436-3030
760-744-6081
WEBSITE
www.tycoelectronics.com
www.amphenolrf.com
www.avxcorp.com
www.digikey.com
www.emersonnetworkpower.com
www.keyelco.com
www.maxim-ic.com
www.murata.com
www.sullinselectronics.com
www.ti.com
Note: Indicate that you are using the MAX2117 when contacting these component suppliers.
Quick Start
Test Equipment Required
? One dual-output power supply capable of supplying
up to 3.3V at > 160mA for V CC and 3V at > 50μA for
V GC gain control voltage
? One RF signal generator capable of delivering at
least 0dBm of output power at frequencies up to
1GHz
? One RF spectrum analyzer capable of covering the
operating frequency range of the device
? One PC (486DX33 or better) with Windows ?
95/98/2000/NT, Windows 4.0/XP ? , or later operating
system, 64MB of memory, and an available parallel
port
? One 25-pin parallel cable
? One multichannel digital oscilloscope (optional)
? One network analyzer to measure return loss (optional)
? One ammeter to measure supply current (optional)
Procedure
The EV kit is fully assembled and factory tested. Follow
input. Note that the input power to the device must be
adjusted to account for the -6dB power loss of the
matching resistor network.
Connections and Setup
This section provides a step-by-step guide to testing
the basic functionality of the EV kit in UHF mode.
Caution: Do not turn on DC power or RF signal gen-
erators until all connections are completed.
1) Verify that all jumpers are in place.
2) With its output disabled, connect the DC power
supply to VGC set to 0.5V (maximum gain).
3) With its output disabled, set the DC power supply
to 3.3V. Connect the power supply to the VCC
(through an ammeter if desired) and GND termi-
nals on the EV kit. If available, set the current limit
to 200mA.
4) With its output disabled, set the RF signal genera-
tor to a 955MHz frequency at -69dBm to account
for the 6dB resistive pad loss. When measuring
noise figure, this 6dB must also be accounted for
by subtracting 6dB from the measured noise fig-
ure, unless the pad has been removed.
the instructions in the Connections and Setup section
for proper device evaluation.
Measurement Considerations
The EV kit includes on-board matching circuitry at the
MAX2117 RF input to convert the 50 ? source to a 75 ?
Windows and Windows XP are registered trademarks of Microsoft Corp.
5)
6)
Connect the output of the RF signal generator to
the SMA connector labeled RF _INPUT on the eval-
uation board.
Connect a 25-pin parallel cable between the PC’s
parallel port and the EV kit board.
_______________________________________________________________________________________
3
相关PDF资料
PDF描述
MAX2120EVKIT+ KIT EVAL FOR MAX2120
MAX2121EVKIT# KIT EVAL FOR MAX2121
MAX2130EVKIT EVAL KIT MAX2130
MAX2140EVKIT EVAL KIT MAX2140
MAX2150ETI+T IC MODULATOR I/Q WIDE 28TQFN
相关代理商/技术参数
参数描述
MAX2117EVKIT+ 功能描述:射频开发工具 MAX2117 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
MAX2118 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Complete DBS Direct-Conversion Tuner ICs with Monolithic VCOs
MAX2118EVKIT 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:MAX2116 Evaluation Kits
MAX2118UGL 功能描述:调谐器 RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度:
MAX2118UGL-T 功能描述:调谐器 RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: