- 您现在的位置：买卖IC网 > PDF目录18709 > MAX2165EVKIT (Maxim Integrated)DVB-H TUNER PDF资料下载
参数资料
| 型号： | MAX2165EVKIT |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/24页 |
| 文件大小： | 0K |
| 描述： | DVB-H TUNER |
| 标准包装： | 1 |
| 系列： | * |
Single-Conversion DVB-H Tuner
To close the RF gain-control loop, connect the 300μA
control current sink of the power detector (pin
OVLD_DET) to V CC with a 40k ? pullup resistor. The
resulting voltage is fed with an RC lowpass to the
RF_AGC input.
VCO Autotuner
The MAX2165 includes 3 VCOs with each VCO contain-
ing 8 VCO sub-bands. The appropriate VCO and VCO
sub-band for the desired local oscillator frequency can
be manually selected by programming the VCO[1:0]
and SB[2:0] bits in the VCO control register (Table 11).
Alternatively, the MAX2165 can be set to autonomously
choose a VCO and VCO sub-band. Automatic VCO
selection is enabled by setting the VAS bit in the VCO
Control register (Table 11). The autotuner begins
selecting the appropriate VCO once the fractional por-
tion of the N-divider has been programmed. Therefore,
when changing LO frequencies, all the N-divider regis-
ters (integer and fractional) must be programmed to
activate the autotuner function.
PLL lock detection can be achieved by monitoring the
MUX pin or by reading the LD bit in the Chip-Status
Readback register (Table 18).
Charge-Pump Current Selection
The PLL charge-pump current can also be either manu-
ally programmed or automatically selected by the VCO
autotuner. Program the CPS bit in the PLL configuration
register (Table 8) to 1 to enable automatic charge-
Table 21. ROM Table
MSB
pump-current selection, or program CPS to 0 to enable
manual charge-pump-current selection. The autotuner
function must be enabled (VAS = 1) to enable automat-
ic charge-pump-current selection. When in manual
mode, the charge-pump current is programmed by the
ICP bit in the PLL Configuration register.
VCO Autotuner Delay Selection
During the autotuner selection process, the autotuner
must allow time for the PLL to settle before determining
if VCO selection was successful. This wait time is pro-
grammable through the ADLY[1:0] bits in the PLL
Configuration register (Table 8). Program the wait time
to be longer than the expected PLL settling time.
RF Notch Filter
The MAX2165 integrates an RF notch filter that can be
used to notch out large interfering signals in the
830MHz to 950MHz frequency range to prevent perfor-
mance degradation when operating in the presence of
large cellular phone signals. The notch frequency of the
filter is programmable through the TF_NTCH[3:0] bits in
the Tracking Filter register (Table 6). Optimal notch fil-
ter codes for two different notch frequencies are stored
in an on-chip ROM table. See the Baseband Filter and
Tracking Filter section for additional details. When no
interfering cellular signals are present or when receiving
signals in the 783MHz to 860MHz frequency range, the
TF_NTCH[3:0] bits must be programmed to 111 to move
the notch out to the highest possible frequency to mini-
mize the filter’s in-band attenuation.
LSB
DESCRIPTION
ADDRESS
DATA BYTE
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
0x0
X
X
X
X
X
X
X
X
Optimal tracking
filter notch settings
TF_NTCH[3:0]
TF_NTCH[3:0]
for operation
below 725MHz
and above
725MHz
Optimal tracking
settings at
780MHz and
470MHz
Optimal baseband
0x1
0x2
Tracking filter notch low
Recommended notch frequency settings for Rx
frequencies below 725MHz
TF_BAL[3:0]
Optimal tracking filter settings at 780MHz
BB_BW[3:0]
Tracking filter notch high
Recommended notch frequency settings for Rx
frequencies above 725MHz
TF_BAL[3:0]
Optimal tracking filter settings at 470MHz
filter BW for 8MHz
0x3
X
X
X
X
channel
8MHz wide
18
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| GLAC01A | SWITCH SIDE-ROTRY SNAP SPDT |
| GLAC03A | SWITCH SIDE-ROTRY SLO ACT |
| UPC8195K-A | IC I/Q MODULATOR AGC 20-QFN |
| GLAA03B | SWITCH TOP PLUNGER SLO ACT 10A |
| CB-OWSPA311GI-00 | KIT START OEM WIRELESS LAN USB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2165EVKIT+ | 功能描述:射频开发工具 MAX2165 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX2169ETL+ | 功能描述:调谐器 Multiband Tuner for Mobile Multi-Media RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX2169ETL+T | 功能描述:调谐器 Multiband Tuner for Mobile Multi-Media RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX2169EVKIT# | 功能描述:射频开发工具 MAX2169 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX216CPN | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。