参数资料
型号: MAX221EUE+
厂商: Maxim Integrated Products
文件页数: 7/8页
文件大小: 0K
描述: IC TX RS232 5V 1UA SHTDN 16TSSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 96
类型: 收发器
驱动器/接收器数: 1/1
规程: RS232
电源电压: 4.5 V ~ 5.5 V
安装类型: 表面贴装
封装/外壳: 16-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 16-TSSOP
包装: 管件
产品目录页面: 1400 (CN2011-ZH PDF)
Applications Information
Using
INVALID
INVALID indicates when an RS-232 signal is present at
the receiver input, and therefore when the port is in use.
INVALID can be used in alternative shutdown control
schemes where it relieves the processor from constantly
polling the port for activity.
Capacitor Selection
The capacitor type used for C1–C4 is not critical for
proper operation; either polarized or nonpolarized
capacitors are acceptable. If polarized capacitors are
used, connect polarity as shown in the
Typical Operating
Circuit. The charge pump requires 0.1F capacitors.
Increasing the capacitor values (e.g., by a factor of 2)
reduces ripple on the transmitter output and slightly
reduces power consumption. C2, C3, and C4 can be
increased without changing C1’s value. However, do not
increase C1’s value without also increasing the values of
C2, C3, and C4 to maintain the proper ratios (C1 to the
other capacitors).
When using the minimum 0.1F capacitors, make sure
the capacitance does not degrade excessively with
temperature. If in doubt, use capacitors with a larger
nominal value. The capacitor’s equivalent series resis-
tance (ESR) usually rises at low temperatures and influ-
ences the amount of ripple on V+ and V-.
Power-Supply Decoupling
In most circumstances, a 0.1F VCC bypass capacitor
is adequate. In applications that are sensitive to power-
supply noise, use a capacitor of the same value as the
charge-pump capacitor C1. Connect bypass capaci-
tors as close to the IC as possible.
Transmitter Output when
Exiting Shutdown
Figure 5 shows the transmitter output when exiting shut-
down mode. The transmitter is loaded with 3k
in paral-
lel with 2500pF. The transmitter output displays no
ringing or undesirable transients as the MAX221 comes
out of shutdown. Note that the transmitter is enabled only
when the magnitude of V- exceeds approximately 3V.
High Data Rates
The MAX221 maintains the RS-232 ±5.0V minimum
transmitter output voltage even at high data rates.
Figure 6 shows a transmitter loopback test circuit.
Figure 7 shows the loopback test result at 120kbps,
and Figure 8 shows the same test at 250kbps.
MAX221
+5V, 1A, Single RS-232 Transceiver
with AutoShutdown
_______________________________________________________________________________________
7
FORCEON
MASTER SHDN LINE
0.1
F1M
FORCEOFF
MAX221
POWER-
MANAGEMENT
UNIT
Figure 4. AutoShutdown with Initial Turn-On to Wake Up a
Mouse or Another System
V-
VCC
0
V+
0
VCC
tINVL
tWU
INVALID
REGION
RECEIVER
INPUT
VOLTAGE
(V)
INVALID
OUTPUT
(V)
tINVH
TRANSMITTER ENABLED, INVALID HIGH
RECEIVER
INPUT
LEVEL
AUTOSHUTDOWN, TRANSMITTER DISABLED,
1
A SUPPLY CURRENT, INVALID LOW
TRANSMITTER ENABLED, INVALID HIGH
-2.7V
-0.3V
+2.7V
+0.3V
0
INDETERMINATE
b)
a)
Figure 3. AutoShutdown Trip Levels
相关PDF资料
PDF描述
VI-24N-IW-F4 CONVERTER MOD DC/DC 18.5V 100W
VE-25J-IV-B1 CONVERTER MOD DC/DC 36V 150W
UP050CH3R3K-A-B CAP CER 3.3PF 50V 10% AXIAL
VE-254-IV-B1 CONVERTER MOD DC/DC 48V 150W
UP050CH2R7K-NAC CAP CER 2.7PF 50V 10% AXIAL
相关代理商/技术参数
参数描述
MAX221EUE+ 功能描述:RS-232接口集成电路 5V 1uA Single RS-232 Txr w/AutoShut RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装:
MAX221EUE+T 功能描述:RS-232接口集成电路 5V 1uA Single RS-232 Txr w/AutoShut RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装:
MAX221EUE-T 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装:
MAX222 制造商:TI 制造商全称:Texas Instruments 功能描述:5-V DUAL RS-232 LINE DRIVER/RECEIVER WITH +-15-kV ESD PROTECTION
MAX2222EBP 制造商:Maxim Integrated Products 功能描述:UCSP CELLULAR-BAND CDMA PA - Rail/Tube