参数资料
型号: MAX232ECSE+
厂商: Maxim Integrated Products
文件页数: 3/26页
文件大小: 0K
描述: IC TXRX RS232 5V ESD-PROT 16SOIC
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 50
类型: 收发器
驱动器/接收器数: 2/2
规程: RS232
电源电压: 4.5 V ~ 5.5 V
安装类型: 表面贴装
封装/外壳: 16-SOIC(0.154",3.90mm 宽)
供应商设备封装: 16-SOIC
包装: 管件
产品目录页面: 1401 (CN2011-ZH PDF)
±15kV ESD-Protected, +5V RS-232 Transceivers
V+
V-
200
μs/div
3V
0V
10V
5V
0V
-5V
-10V
SHDN
MAX211E
Figure 5. MAX211E V+ and V- when Exiting Shutdown (0.1F
capacitors)
X = Don't care.
*
Active = active with reduced performance
SHDN
E
EN
N
OPERATION
STATUS
Tx
Rx
0
Normal
Operation
All Active
0
1
Normal
Operation
All Active
All High-Z
1
X
Shutdown
All High-Z
Table 1a. MAX205E/MAX206E/MAX211E/
MAX241E Control Pin Configurations
Table 1b. MAX213E Control Pin
Configurations
The MAX213E’s receiver propagation delay is typically
0.5s in normal operation. In shutdown mode,
propagation delay increases to 4s for both rising and
falling transitions. The MAX213E’s receiver inputs have
approximately 0.5V hysteresis, except in shutdown,
when receivers R4 and R5 have no hysteresis.
When entering shutdown with receivers active, R4 and
R5 are not valid until 80s after SHDN is driven low.
When coming out of shutdown, all receiver outputs are
invalid until the charge pumps reach nominal voltage
levels (less than 2ms when using 0.1F capacitors).
±15kV ESD Protection
As with all Maxim devices, ESD-protection structures
are incorporated on all pins to protect against
electrostatic discharges encountered during handling
and assembly. The driver outputs and receiver inputs
have extra protection against static electricity. Maxim’s
engineers developed state-of-the-art structures to
protect these pins against ESD of ±15kV without
damage. The ESD structures withstand high ESD in all
states: normal operation, shutdown, and powered
down. After an ESD event, Maxim’s E versions keep
working without latchup, whereas competing RS-232
products can latch and must be powered down to
remove latchup.
ESD protection can be tested in various ways; the
transmitter outputs and receiver inputs of this product
family are characterized for protection to the following
limits:
1) ±15kV using the Human Body Model
2) ±8kV using the contact-discharge method specified
in IEC1000-4-2
3) ±15kV using IEC1000-4-2’s air-gap method.
ESD Test Conditions
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test set-up, test methodology, and test results.
Human Body Model
Figure 6a shows the Human Body Model, and Figure
6b shows the current waveform it generates when
discharged into a low impedance. This model consists
of a 100pF capacitor charged to the ESD voltage of
interest, which is then discharged into the test device
through a 1.5k
Ω resistor.
S
SH
HD
DN
N EN
OPERATION
STATUS
Tx 1–4
0
Shutdown
All High-Z
0
1
Shutdown
All High-Z
1
0
Normal
Operation
1
Normal
Operation
All Active
Active
1–3
4, 5
High-Z
Active
High-Z
Active*
High-Z
Rx
Maxim Integrated
11
MAX202E–MAX213E, MAX232E/MAX241E
相关PDF资料
PDF描述
MAX3224CAP+ IC TXRX RS232 250KBPS SD 20-SSOP
VI-B1F-IV-F3 CONVERTER MOD DC/DC 72V 150W
VI-BWJ-MX-F1 CONVERTER MOD DC/DC 36V 75W
VI-BWJ-MW CONVERTER MOD DC/DC 36V 100W
VI-BW3-MX-F4 CONVERTER MOD DC/DC 24V 75W
相关代理商/技术参数
参数描述
MAX232ECSE 制造商:Maxim Integrated Products 功能描述:DUAL TRANSCEIVER SMD SOIC16 232
MAX232ECSE+ 功能描述:RS-232接口集成电路 15kV ESD-Protected 5V RS232 Transceiver RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装:
MAX232ECSE+T 功能描述:RS-232接口集成电路 15kV ESD-Protected 5V RS232 Transceiver RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装:
MAX232ECSE-T 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装:
MAX232ECWE 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: