- 您现在的位置：买卖IC网 > PDF目录380347 > MAX244 (Maxim Integrated Products, Inc.) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF资料下载
参数资料
| 型号： | MAX244 |
| 厂商： | Maxim Integrated Products, Inc. |
| 元件分类： | RS-232 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | 5V的高速RS - 232收发器与0.1uF电容 |
| 文件页数： | 14/36页 |
| 文件大小： | 442K |
| 代理商： | MAX244 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
M
_______________Detailed Description
The MAX220–MAX249 contain four sections: dual
charge-pump DC-DC voltage converters, RS-232 dri-
vers, RS-232 receivers, and receiver and transmitter
enable control inputs.
Dual Charge-Pump Voltage Converter
The MAX220–MAX249 have two internal charge-pumps
that convert +5V to ±10V (unloaded) for RS-232 driver
operation. The first converter uses capacitor C1 to dou-
ble the +5V input to +10V on C3 at the V+ output. The
second converter uses capacitor C2 to invert +10V to
-10V on C4 at the V- output.
A small amount of power may be drawn from the +10V
(V+) and -10V (V-) outputs to power external circuitry
(see the
Typical Operating Characteristics
section),
except on the MAX225 and MAX245–MAX247, where
these pins are not available. V+ and V- are not regulated,
so the output voltage drops with increasing load current.
Do not load V+ and V- to a point that violates the mini-
mum ±5V EIA/TIA-232E driver output voltage when
sourcing current from V+ and V- to external circuitry.
When using the shutdown feature in the MAX222,
MAX225, MAX230, MAX235, MAX236, MAX240,
MAX241, and MAX245–MAX249, avoid using V+ and V-
to power external circuitry. When these parts are shut
down, V- falls to 0V, and V+ falls to +5V. For applica-
tions where a +10V external supply is applied to the V+
pin (instead of using the internal charge pump to gen-
erate +10V), the C1 capacitor must not be installed and
the
SHDN
pin must be tied to V
CC
. This is because V+
is internally connected to V
CC
in shutdown mode.
RS-232 Drivers
The typical driver output voltage swing is ±8V when
loaded with a nominal 5k
RS-232 receiver and V
CC
=
+5V. Output swing is guaranteed to meet the EIA/TIA-
232E and V.28 specification, which calls for ±5V mini-
mum driver output levels under worst-case conditions.
These include a minimum 3k
load, V
CC
= +4.5V, and
maximum operating temperature. Unloaded driver out-
put voltage ranges from (V+ -1.3V) to (V- +0.5V).
Input thresholds are both TTL and CMOS compatible.
The inputs of unused drivers can be left unconnected
since 400k
input pull-up resistors to V
CC
are built in
(except for the MAX220). The pull-up resistors force the
outputs of unused drivers low because all drivers invert.
The internal input pull-up resistors typically source 12μA,
except in shutdown mode where the pull-ups are dis-
abled. Driver outputs turn off and enter a high-imped-
ance state—where leakage current is typically
microamperes (maximum 25μA)—when in shutdown
mode, in three-state mode, or when device power is
removed. Outputs can be driven to ±15V. The power-
supply current typically drops to 8μA in shutdown mode.
The MAX220 does not have pull-up resistors to force the
ouputs of the unused drivers low. Connect unused inputs
to GND or V
CC
.
The MAX239 has a receiver three-state control line, and
the MAX223, MAX225, MAX235, MAX236, MAX240,
and MAX241 have both a receiver three-state control
line and a low-power shutdown control. Table 2 shows
the effects of the shutdown control and receiver three-
state control on the receiver outputs.
The receiver TTL/CMOS outputs are in a high-imped-
ance, three-state mode whenever the three-state enable
line is high (for the MAX225/MAX235/MAX236/MAX239–
MAX241), and are also high-impedance whenever the
shutdown control line is high.
When in low-power shutdown mode, the driver outputs
are turned off and their leakage current is less than 1μA
with the driver output pulled to ground. The driver output
leakage remains less than 1μA, even if the transmitter
output is backdriven between 0V and (V
CC
+ 6V). Below
-0.5V, the transmitter is diode clamped to ground with
1k
series impedance. The transmitter is also zener
clamped to approximately V
CC
+ 6V, with a series
impedance of 1k
.
The driver output slew rate is limited to less than 30V/μs
as required by the EIA/TIA-232E and V.28 specifica-
tions. Typical slew rates are 24V/μs unloaded and
10V/μs loaded with 3
and 2500pF.
RS-232 Receivers
EIA/TIA-232E and V.28 specifications define a voltage
level greater than 3V as a logic 0, so all receivers invert.
Input thresholds are set at 0.8V and 2.4V, so receivers
respond to TTL level inputs as well as EIA/TIA-232E and
V.28 levels.
The receiver inputs withstand an input overvoltage up
to ±25V and provide input terminating resistors with
+5V-Powered, Multichannel RS-232
Drivers/Receivers
14
______________________________________________________________________________________
PART
SHDN
EN
EN(R)
RECEIVERS
MAX223
__
Low
High
High
X
Low
High
High Impedance
Active
High Impedance
MAX225
__
__
High Impedance
Active
__
MAX235
MAX236
MAX240
Low
Low
High
__
__
Low
High
X
High Impedance
Active
High Impedance
Table 2. Three-State Control of Receivers
Low
High
SHDN
__
相关PDF资料 |
PDF描述 |
|---|---|
| MAX244C | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX244CQH | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX244D | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX244EQH | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX245 | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX24405EXG+ | 制造商:Microsemi Corporation 功能描述:Clock Multiplier/Synthesizer 81-Pin CSBGA 制造商:Microsemi Corporation 功能描述:5 OUT ANY-RATE CLOCK MULTIPLIER - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CLK MULT 5-OUTPUT 制造商:Microsemi Corporation 功能描述:IC CLK MULT 5-OUTPUT 制造商:Microsemi Corporation 功能描述:MAX24405 Series 5 Output 750 Mhz Any-Rate Clock Multiplier - CSBGA-81 |
| MAX2440EAI | 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MAX2440EAI+ | 功能描述:射频接收器 Integrated Circuits (ICs) RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MAX2440EAI+T | 功能描述:射频接收器 Integrated Circuits (ICs) RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MAX2440EAI-T | 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。