- 您现在的位置：买卖IC网 > PDF目录18710 > MAX2609EVKIT (Maxim Integrated)EVAL KIT PDF资料下载
参数资料
| 型号： | MAX2609EVKIT |
| 厂商： | Maxim Integrated |
| 文件页数： | 4/15页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT |
| 标准包装： | 1 |
| 系列： | * |
MAX2605–MAX2609
45MHz to 650MHz, Integrated IF
VCOs with Differential Output
AC ELECTRICAL CHARACTERISTICS (continued)
(MAX2605–MAX2609 EV kits, V CC = +2.7V to +5.5V, V TUNE = 0.4V to 2.4V, T A = -40°C to +85°C, unless otherwise noted. Typical val-
ues are at V CC = +2.75V, V TUNE = 1.5V, and T A = +25°C.) (Note 1)
PARAMETER
Even-Order Harmonics
CONDITIONS
Differential, R L = 50 ? each side
MIN
TYP
-30
MAX
UNITS
dBc
MAX2605
MAX2606
60
120
Supply Pushing (Note 9)
MAX2607
MAX2608
MAX2609
220
480
720
kHz/V
Note 1: Production tested at T A = +25°C. Maximum and minimum over temperature limits are guaranteed by design and
characterization.
Note 2: Supply current is measured while the part is oscillating and inductor Q ≥ Q MIN . For MAX2605/MAX2606/MAX2607, Q MIN = 35;
for MAX2608/MAX2609, Q MIN = 40.
Note 3: The DC output current is the total available output signal current.
Note 4: Application range of the part is achieved using external inductance as specified in Figures 1-5 and shown in Figure 6. The inter-
nal varactors support center frequencies of 45MHz to 650MHz. The center frequency is defined by the value of the external
inductor element, L F . The application frequency limits are guaranteed by design and characterization.
Note 5: The guaranteed (tested) limits ? MIN and ? MAX are measured at V TUNE = 0.4V and V TUNE = 2.4V, respectively. Passing
requirements are: ? ≤ ? MIN at V TUNE = 0.4 and ? ≥ ? MAX at V TUNE = 2.4V. The nominal frequency of oscillation is defined by
the inductor.
Note 6: Describes peak tuning gain, which occurs at V TUNE = 0.4V.
Note 7: Measurement at OUT+ or OUT- matched for optimum power transfer into 50 ? load near the center of the operating frequency
range.
Note 8: The phase-noise specifications listed apply to the typical operating circuit shown in Figure 6. Apply over the entire operating
frequency range of the MAX2605–MAX2609.
Note 9: Supply pushing is measured with V CC stepped from +2.7V to +3.2V.
Typical Operating Characteristics
(MAX260_ EV kit, V CC = +2.75V, V TUNE = 1.4V, T A = +25°C, unless otherwise noted.)
4.0
SUPPLY CURRENT
vs. TEMPERATURE
0.10
TUNE INPUT LEAKAGE CURRENT
vs. TEMPERATURE
65
MAX2605
VCO TUNING CURVE
3.5
3.0
MAX2609
MAX2608 MAX2607
MAX2606
0.08
60
0.06
2.5
55
0.04
2.0
50
1.5
MAX2605
0.02
1.0
0
45
-40
-20
0
20
40
60
80
-40
-20
0
20
40
60
80
0
0.5
1.0
1.5
2.0
2.5
3.0
4
TEMPERATURE (°C)
TEMPERATURE ( ° C)
V TUNE (V)
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX2607EVKIT | EVAL KIT |
| MAX2661EVKIT | EVAL KIT |
| MAX2206EVKIT | EVAL KIT |
| MAX2473EVKIT | EVAL KIT MAX2472, MAX2473 |
| MAX2471EVKIT | EVAL KIT MAX2470, MAX2471 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX260ACNG | 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
| MAX260ACNG+ | 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
| MAX260ACWG | 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
| MAX260ACWG+ | 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
| MAX260ACWG+T | 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。