参数资料
型号: MAX262BCNG+
厂商: Maxim Integrated Products
文件页数: 9/26页
文件大小: 0K
描述: IC FILTER ACT MPU PROG 24-DIP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 15
滤波器类型: 通用开关电容器
频率 - 截止或中心: 140kHz
滤波器数: 2
滤波器阶数: 2nd
电源电压: 4.74 V ~ 12.6 V,±2.37 V ~ 6.3 V
安装类型: 通孔
封装/外壳: 24-DIP(0.300",7.62mm)
供应商设备封装: 24-PDIP
包装: 管件
MAX260/MAX261/MAX262
Microprocessor Programmable
Universal Active Filters
______________________________________________________________________________________
17
Mode 1, along with mode 4, supports the highest clock
frequencies (see Table 1) because the input summing
amplifier is outside the filter’s resonant loop (Figure 7).
The gain of the lowpass and notch outputs is 1, while
the bandpass gain at the center frequency is Q. For
bandpass gains other than Q, the filter input or output
can be scaled by a resistive divider or op amp.
MODE 2 (Figure 8) is used for all-pole lowpass and
bandpass filters. Key advantages compared to mode 1
are higher available Qs (see Table 3) and lower output
noise. Mode 2’s available fCLK/f0 ratios are
√2 less than
with mode 1 (see Table 2), so a wider overall range of
f0s can be selected from a single clock when both
modes are used together. This is demonstrated in the
Wide Passband Chebyshev Bandpass design example.
MODE 3 (Figure 9) is the only mode that produces
high-pass filters. The maximum clock frequency is
somewhat less than with mode 1 (see Table 1).
MODE 3A (Figure 10) uses a separate op amp to sum
the highpass and lowpass outputs of mode 3, creating
a separate notch output. This output allows the notch to
be set independently of f0 by adjusting the op amp’s
feedback resistor ratio (RH, RL). RH, RL, and RG are
external resistors. Because the notch can be indepen-
dently set, mode 3A is also useful when designing
pole-zero filters such as elliptics.
MODE 4 (Figure 11) is the only mode that provides an
allpass output. This is useful when implementing group
delay equalization. In addition to this, mode 4 can also
be used in all pole lowpass and bandpass filters. Along
with mode 1, it is the fastest operating mode for the fil-
ter, although the gains are different than in mode 1.
When the allpass function is used, note that some
amplitude peaking occurs (approximately 0.3dB when
Q = 8) at f0. Also note that f0 and Q sampling errors are
highest in mode 4 (see Figure 20).
SCN
IN
SCN
N
BP
LP
+
-
MODE 2
+
-
SCN
Σ
Figure 8. Filter Mode 2: Second-Order Bandpass, Lowpass,
and Notch
SCN
IN
SCN
HP
BP
LP
+
-
MODE 3
+
-
SCN
Σ
SCN = SWITCHED-CAPACITOR NETWORK
Figure 9. Filter Mode 3: Second-Order Bandpass, Lowpass,
and Highpass
SCN
IN
SCN
HP
RG
RH
RL
BP
LP
+
-
MODE 3A
N
+
-
+
-
SCN
Σ
SCN = SWITCHED-CAPACITOR NETWORK
Figure 10. Filter Mode 3a: Second-Order Bandpass, Lowpass,
Highpass, and Notch. For elliptic LP, BP, HP, and Notch, the N
output is used.
相关PDF资料
PDF描述
VE-B2R-IY-B1 CONVERTER MOD DC/DC 7.5V 50W
VE-B2M-IY-B1 CONVERTER MOD DC/DC 10V 50W
VE-B03-IY-F1 CONVERTER MOD DC/DC 24V 50W
MAX271CWG+ IC FILTER LOWPASS PROG 24-SOIC
MAX263BCPI+ IC FILTER BANDPASS PROG 28-DIP
相关代理商/技术参数
参数描述
MAX262BCNG+ 功能描述:有源滤波器 MPU Programmable Universal RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube
MAX262BCWG 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube
MAX262BCWG+ 功能描述:有源滤波器 MPU Programmable Universal RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube
MAX262BCWG+T 功能描述:有源滤波器 MPU Programmable Universal RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube
MAX262BCWG-T 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube