- 您现在的位置：买卖IC网 > Datasheet目录473 > MAX2830EVKIT+ (Maxim Integrated)KIT EVAL FOR MAX2830 Datasheet资料下载
参数资料
| 型号： | MAX2830EVKIT+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 25/33页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX2830 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 收发器，802.11 b/g |
| 频率： | 2.4GHz ~ 2.5GHz |
| 适用于相关产品： | MAX2830 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页
MAX2830
2.4GHz to 2.5GHz 802.11g/b RF Transceiver, PA,
and Rx/Tx/Antenna Diversity Switch
Table 14. IEEE 802.11g/b Divider-Ratio Programming Words
f RF
(MHz)
(f RF / f COMP )
INTEGER DIVIDER
A3:A0 = 0011, D7:D0
FRACTIONAL DIVIDER
A3:A0 = 0100, D13:D0 A3:A0 = 0011, D13:D8
2412
2417
2422
2427
2432
2437
2442
2447
2452
2457
2462
2467
2472
2484
120.6
120.85
121.1
121.35
121.6
121.85
122.1
122.35
122.6
122.85
123.1
123.35
123.6
124.2
0111 1000b
0111 1000b
0111 1001b
0111 1001b
0111 1001b
0111 1001b
0111 1010b
0111 1010b
0111 1010b
0111 1010b
0111 1011b
0111 1011b
0111 1011b
0111 1100b
2666h
3666h
0666h
1666h
2666h
3666h
0666h
1666h
2666h
3666h
0666h
1666h
2666h
0CCCh
1Ah
1Ah
1Ah
1Ah
1Ah
1Ah
1Ah
1Ah
1Ah
1Ah
1Ah
1Ah
1Ah
33h
Crystal Oscillator
The crystal oscillator has been optimized to work with
low-cost crystals (e.g., Kyocera CX-3225SB). See
Figure 2. The crystal oscillator frequency can be fine
tuned through bits D6:D0 in Register 14 (A3:A0 = 1110),
which control the value of C TUNE from 0.5pF to 15.4pF in
0.12pF steps. See the Crystal-Oscillator Offset
Frequency vs. Crystal-Oscillator Tuning Bits graph in the
Typical Operating Characteristics. The crystal oscillator
can be used as a buffer for an external reference fre-
quency source. In this case, the reference signal is AC-
coupled to the XTAL pin, and capacitors C1 and C2 are
not connected. When used as a buffer, the XTAL input
pin has to be AC-coupled. The XTAL pin has an input
impedance of 5k ? || 4pF, (set D6:D0 = 0000000 in
Register 14 A3:A0 = 1110).
MAX2830
Reference Clock Output Divider/Buffer
The reference oscillator of the MAX2830 has a divider
and a buffered output for routing the reference clock to
the accompanying baseband IC. Bit D10 in Register 14
(A3:A0 = 1110) sets the buffer divider to divide by 1 or
2, independent of the divide ratio for the reference fre-
quency provided to the PLL. Bit B9 in the same register
enables or disables the reference buffer output. See
the Clock Output waveform in the Typical Operating
Characteristics.
Loop Filter
The PLL charge-pump output, CPOUT (pin 24), con-
nects to an external third-order, lowpass RC loop-filter,
which in turn connects to the voltage tuning input,
TUNE (pin 32), of the VCO, completing the PLL loop.
The charge-pump output sink and source current is
1mA, and the VCO tuning gain is 103MHz/V at 0.5V
tune voltage and 86MHz/V at 2.2V tune voltage. The RC
loop-filter values have been optimized for a loop band-
width of 150kHz, to achieve the desired Rx/Tx turn-
around settling time, while maintaining loop stability
XTAL
C1
CTUNE
28
29
and good phase noise. Refer to the MAX2830 EV kit
schematic for the recommended loop-filter component
values. Keep the line from this pin to the tune input as
short as possible to prevent spurious pickup.
C2
C TUNE
1.35k ?
5.9k ?
Lock-Detector Output
The PLL features a logic lock-detect output. A logic-high
indicates the PLL is locked, and a logic-low indicates
FOR EXTERNAL REFERENCE CLOCK SET, C1 = C2 = OPEN
Figure 2. Crystal Oscillator Schematic
Maxim Integrated
the PLL is not locked. Bit D5 in Register 5 (A3:A0 =
0101) enables or disables the lock-detect output. Bit
25
相关PDF资料 |
PDF描述 |
|---|---|
| MAX2831EVKIT+ | KIT EVAL FOR MAX2831 |
| MAX2837EVKIT+ | KIT EVAL FOR MAX2837 |
| MAX2838EVKIT+ | KIT EVAL FOR MAX2838 |
| MAX2839ASEVKIT+ | KIT EVAL FOR MAX2839A WLP |
| MAX2839EVKIT+ | KIT EVAL FOR MAX2839 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2830EVKIT+ | 功能描述:WiFi/802.11开发工具 MAX2830 Eval Kit RoHS:否 制造商:Roving Networks 产品:Evaluation Boards 工具用于评估:RN-171 支持协议:802.11 b/g 频率:2.4 GHz 接口类型:UART 工作电源电压:2 V to 16 V |
| MAX2830SEWU | 功能描述:射频收发器 RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MAX2830SEWU+ | 功能描述:射频收发器 RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MAX2831ETM+ | 功能描述:射频收发器 2.4-2.5GHz 802.11g/b 射频收发器 RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| MAX2831ETM+T | 功能描述:射频收发器 2.4-2.5GHz 802.11g/b 射频收发器 RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。