- 您现在的位置：买卖IC网 > Datasheet目录473 > MAX2852ITK+ (Maxim Integrated)IC RECEIVER DFS 5GHZ 68TQFN Datasheet资料下载
参数资料
| 型号： | MAX2852ITK+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | IC RECEIVER DFS 5GHZ 68TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 30 |
| 频率： | 4.9GHz ~ 5.9GHz |
| 调制或协议： | * |
| 应用： | 通用 |
| 电流 - 接收： | 135mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 特点： | * |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | -25°C ~ 85°C |
| 封装/外壳： | 68-TQFN 裸露焊盘 |
| 供应商设备封装： | 68-TQFN-EP（10x10） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
5GHz Receiver
The AM detector multiplies the Tx RF output signal with
itself. The self-mixing product of the wanted sideband
becomes DC voltage and is filtered on-chip. The mixing
product between wanted sideband and the carrier leak-
age forms Ftone at Rx baseband output. The mixing
product between the wanted sideband and the unwant-
ed sideband forms 2Ftone at Rx baseband output.
RF Loopback
In RF loopback mode, part of the Rx and Tx circuit
blocks (except the LNA) are powered on and active. The
transmitter 4 I/Q input signal is upconverted to RF, and
the output of the transmitter is fed to the receiver down-
converter input. Output signals are delivered to receiver
4 baseband I/Q outputs. The I/Q lowpass filters in the
transmitter signal path are bypassed.
Baseband Loopback
In baseband loopback mode, part of the Rx and Tx
baseband circuit blocks are powered and active. The
transmitter 4 IQ input signal is routed to receiver lowpass
filter input. Output signals are delivered to receiver 4
baseband I/Q outputs.
Power-On Sequence
Set the ENABLE pin to VCC for 2ms to start the crystal
oscillator. Program all SPI addresses according to rec-
ommended values. Set SPI Main address 0 D4:D2 from
000 to 001 to engage standby mode. To lock the LO
frequency, the user can set SPI in order of Main address
15, Main address 16, and then Main address 17 to trig-
ger VCO sub-band autoacquisition; the acquisition will
take 2ms. After the LO frequency is locked, set SPI Main
address 0 D4:D2 = 010 and 011 for Rx and Tx operat-
ing modes, respectively. Before engaging Rx mode, set
Main address 5 D1 = 1 to allow fast DC offset settling.
After engaging Rx mode and Rx baseband DC offset
settles, the user can set Main address 5 D1 = 0 to com-
plete Rx DC offset cancellation.
MICROWIRE is a trademark of National Semiconductor Corp.
Programmable Registers and
4-Wire SPI Interface
The MAX2852 includes 60 programmable 16-bit reg-
isters. The most significant bit (MSB) is the read/write
selection bit (R/W in Figure 1). The next 5 bits are register
address (A4:A0 in Figure 1). The 10 least significant bits
(LSBs) are register data (D9:D0 in Figure 1). Register
data is loaded through the 4-wire SPI/MICROWIRE?-
compatible serial interface. MSB of data at the DIN pin
is shifted in first and is framed by CS . When CS is low,
the clock is active, and input data is shifted at the rising
edge of the clock at SCLK pin. At the CS rising edge,
the 10-bit data bits are latched into the register selected
by address bits. See Figure 1. To support more than a
32-register address using a 5-bit wide address word,
the bit 0 of address 0 is used to select whether the 5-bit
address word is applied to the main address or local
address. The register values are preserved in shutdown
mode as long as the power-supply voltage is maintained.
There is no power-on SPI register self-reset functionality
in the MAX2852, so the user must program all register
values after power-up. During the read mode, register
data selected by address bits is shifted out to the DOUT
pin at the falling edges of the clock.
18
_____________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX2870EVKIT# | EVAL KIT MAX2870 |
| MAX2904EVKIT | EVAL KIT |
| MAX3524EVKIT | EVAL KIT MAX3524 |
| MAX3540EVKIT# | KIT FOR MAX3540 DVB TUNER |
| MAX3541EVKIT+ | KIT FOR MAX3541 DVB TUNER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX2852ITK+ | 功能描述:射频接收器 5Ghz Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MAX2852ITK+T | 功能描述:射频接收器 5Ghz Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| MAX2870ETJ+ | 功能描述:锁相环 - PLL PLL/VCO RoHS:否 制造商:Silicon Labs 类型:PLL Clock Multiplier 电路数量:1 最大输入频率:710 MHz 最小输入频率:0.002 MHz 输出频率范围:0.002 MHz to 808 MHz 电源电压-最大:3.63 V 电源电压-最小:1.71 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:QFN-36 封装:Tray |
| MAX2870ETJ+T | 功能描述:锁相环 - PLL PLL/VCO RoHS:否 制造商:Silicon Labs 类型:PLL Clock Multiplier 电路数量:1 最大输入频率:710 MHz 最小输入频率:0.002 MHz 输出频率范围:0.002 MHz to 808 MHz 电源电压-最大:3.63 V 电源电压-最小:1.71 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:QFN-36 封装:Tray |
| MAX2870EVKIT# | 功能描述:射频开发工具 MAX2870 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
发布紧急采购，3分钟左右您将得到回复。