参数资料
型号: MAX292MJA
厂商: MAXIM INTEGRATED PRODUCTS INC
元件分类: 运动控制电子
英文描述: Analog Filter
中文描述: SWITCHED CAPACITOR FILTER, BESSEL, LOWPASS, CDIP8
封装: CERAMIC, DIP-8
文件页数: 7/13页
文件大小: 352K
代理商: MAX292MJA
Connections and Setup
This section provides step-by-step instructions for get-
ting the EV kits up and running in all operation modes.
1) Verify that shunts JU1, JU2, JU4, JU6, JU7, and
JU9 are in place.
2) Set the power supply to +4V and turn it off.
3) Set the adjustable power supply to +2.1V and turn it off.
4) Connect the ground terminal to GND.
5) Connect the positive +4.0V terminal to VCC.
6) Connect the positive terminal of the adjustable
power supply to VASK.
7) Set the IF generator to 14.56MHz and set the output
level to 200mV. Keep the IF generator output off.
8) Use an SMA cable to connect the output of the IF
generator to the REFIN on the MAX2900
MAX2904
EV kits.
9) Use an SMA cable to connect the RFOUT to the
input of the spectrum analyzer.
10) Set the spectrum analyzer to view the output.
11) Turn on all power supplies and enable the signal
generator.
12) Measure the supply current.
13) Observe the RF output frequency displayed on the
spectrum analyzer.
14) Measure the RF output power.
15) The RF output power should be approximately
23dBm after accounting for cable and connector loss.
Adjustments and Control
Operation Modes
The EV kits support four modes of operation:
SHUTDOWN mode
EN = REFEN = low. (Shunt
pins 2 and 3 of JU1, JU2).
SYNTH mode
EN = REFEN = high, OOKIN = low.
(Shunt pins 1 and 2 of JU1, JU2; shunt pins 2 and 3 of JU4).
TRANSMIT mode
EN = REFEN = OOKIN = high.
(Shunt pins 1 and 2 of JU1, JU2, JU4).
REFERENCE only mode
REFEN = high, EN = low.
(Shunt pins 2 and 3 of JU1. Shunt pins 1 and 2 of JU2).
See Table 1 for jumper selection.
Modulations
The IC supports various modulation modes:
BPSK is obtained through the MODIN pin (JU3).
OOK is obtained digitally with the OOKIN pin (JU4).
ASK is obtained through the VASK pin.
FM is imposed on the VCO or the reference.
Synthesizer Programming
(MAX2900/MAX2901/MAX2903)
The three pins D0, D1, D2 (JU6, JU7, and JU9) are
used as digital entries to program the synthesizer divi-
sion ratios (MAX2900). For MAX2901/MAX2903, pin
DIV63 (JU9) is used to select the division ratio of 62 or
63. Refer to the MAX2900
MAX2904 data sheet for cor-
responding division ratios.
Modulation Filter and Power Management
The RLPF input controls the modulation filter center fre-
quency. Pins PWRSET and VASK are analog inputs
E
MAX2900–MAX2904 Evaluation Kits
_______________________________________________________________________________________
7
JUMPER
MAX2900
MAX2901/
MAX2903
MAX2902/
MAX2904
NAME
DESCRIPTION
1
2
3
4
1
2
3
4
6/7
8
9
1
2
3
4
6/7
8
9
EN
Chip Enable
Reference Enable
BPSK Modulation Input
OOK Modulation Input
Digital Synthesizer Programming Input
VCO Output
REF Output
Digital Synthesizer Programming Input
Digital Synthesizer Programming Input
Not Connected
REFEN
MODIN
OOKIN
D0/D1
VCO+/ VCO-
REFOUT
D2
DIV63
N.C.
6/7
8
9
Table 1. Jumper Description
相关PDF资料
PDF描述
MAX295CSA Analog Filter
MAX295ESA Analog Filter
MAX296CSA Analog Filter
MAX2901EVKIT Evaluation Kits for the MAX2900/MAX2901/MAX2902/MAX2903/MAX2904
MAX2902 200mW Single-Chip Transmitter ICs for 868MHz/915MHz ISM Bands
相关代理商/技术参数
参数描述
MAX293C/D 功能描述:有源滤波器 8th-Order Lowpass Elliptic Switched-Capacitor Filters RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube
MAX293CPA 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube
MAX293CPA+ 功能描述:有源滤波器 8th-Order Lowpass Switched-Cap RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube
MAX293CPA-G095 制造商:Maxim Integrated Products 功能描述:
MAX293CSA 功能描述:有源滤波器 RoHS:否 制造商:Maxim Integrated 通道数量:1 截止频率:150 KHz 电源电压-最大:11 V 电源电压-最小:4.74 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP N 封装:Tube