- 您现在的位置：买卖IC网 > PDF目录11818 > MAX3100CEE (Maxim Integrated Products)IC UART SPI/MICRWIRE COMP 16QSOP PDF资料下载
参数资料
| 型号： | MAX3100CEE |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/24页 |
| 文件大小： | 0K |
| 描述： | IC UART SPI/MICRWIRE COMP 16QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 特点： | 低功率 |
| 通道数： | 1，UART |
| FIFO's： | 8 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
SPI/MICROWIRE-Compatible
UART in QSOP-16
Detailed Description
The MAX3100 universal asynchronous receiver trans-
mitter (UART) interfaces the SPI/MICROWIRE-compati-
ble, synchronous serial data from a microprocessor
(P) to asynchronous, serial-data communication ports
(RS-232, RS-485, IrDA). Figure 2 shows the MAX3100
functional diagram.
The MAX3100 combines a simple UART and a baud-
rate generator with an SPI interface and an interrupt
generator. Configure the UART by writing a 16-bit word
to a write-configuration register, which contains the
baud rate, data-word length, parity enable, and enable
of the 8-word receive first-in/first-out (FIFO). The write
configuration selects between normal UART timing and
IrDA timing, controls shutdown, and contains 4 interrupt
mask bits.
Transmit data by writing a 16-bit word to a write-data
register, where the last 7 or 8 bits are actual data to be
transmitted. Also included is the state of the transmitted
parity bit (if enabled). This register controls the state of
the RTS output pin. Received words generate an inter-
rupt if the receive-bit interrupt is enabled.
Read data from a 16-bit register that holds the oldest
data from the receive FIFO, the received parity data,
and the logic level at the CTS input pin. This register
also contains a bit that is the framing error in normal
operation and a receive-activity indicator in shutdown.
The baud-rate generator determines the rate at which
the transmitter and receiver operate. Bits B0 to B3 in
the write-configuration register determine the baud-rate
divisor (BRD), which divides down the X1 oscillator fre-
quency. The baud clock is 16 times the data rate (baud
rate).
Pin Description
PIN
QSOP
DIP
TQFN-EP
NAME
FUNCTION
1
23
DIN
SPI/MICROWIRE Serial-Data Input. Schmitt-trigger input.
2
DOUT
SPI/MICROWIRE Serial-Data Output. High impedance when CS is high.
3
SCLK
SPI/MICROWIRE Serial-Clock Input. Schmitt-trigger input.
444
CS
Active-Low Chip-Select Input. DOUT goes high impedance when CS is high,
IRQ, TX, and RTS are always active. Schmitt-trigger input.
655
IRQ
Active-Low Interrupt Output. Open-drain interrupt output to microprocessor.
768
SHDN
Hardware-Shutdown Input. When shut down (SHDN = 0), the oscillator turns
off immediately without waiting for the current transmission to end, reducing
supply current to just leakage currents.
8
7
9
GND
Ground
9
8
10
X2
Crystal Connection. Leave X2 unconnected for external clock. See Crystal-
Oscillator Operation—X1, X2 Connection section.
10
9
11
X1
Crystal Connection. X1 also serves as an external clock input. See Crystal-
Oscillator Operation—X1, X2 Connection section.
11
10
15
CTS
General-Purpose Active-Low Input. Read via the CTS register bit; often used
for RS-232 clear-to-send input (Table 1).
13
11
16
RTS
General-Purpose Active-Low Output. Controlled by the CTS register bit. Often
used for RS-232 request-to-send output or RS-485 driver enable.
14
12
17
RX
Asynchronous Serial-Data (receiver) Input. The serial information received
from the modem or RS-232/RS-485 receiver. A transition on RX while in
shutdown generates an interrupt (Table 5).
15
13
21
TX
Asynchronous Serial-Data (transmitter) Output
16
14
22
VCC
Positive Supply Pin (2.7V to 5.5V)
5, 12
—
1, 6, 7, 12,
13, 14, 18,
19, 20, 24
N.C.
No Connection. Not internally connected.
—
EP
Exposed Pad. Connect EP to ground or leave unconnected.
MAX3100
Maxim Integrated
5
MAX3100
相关PDF资料 |
PDF描述 |
|---|---|
| IS82C52 | IC PERIPH UART/BRG 16MHZ 28-PLCC |
| IP82C52 | IC UART/BRG PERIPHERAL 28-DIP |
| ID82C52 | IC UART/BRG 5V 16MHZ 28-DIP |
| IS82C52Z | IC CONTROLLER UART 28-PLCC |
| IS82C52Z96 | IC CTRLR CMOS SERIAL 28-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3100CEE | 制造商:Maxim Integrated Products 功能描述:SPI MICROWIRE-COMPATIBLE SMD 3100 |
| MAX3100CEE+ | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3100CEE+T | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3100CEE-T | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3100CPD | 功能描述:UART 接口集成电路 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。