- 您现在的位置：买卖IC网 > PDF目录11812 > MAX3100CPD (Maxim Integrated Products)IC UART SPI MICROCOMPATBL 14-DIP PDF资料下载
参数资料
| 型号： | MAX3100CPD |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC UART SPI MICROCOMPATBL 14-DIP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 25 |
| 特点： | 低功率 |
| 通道数： | 1，UART |
| FIFO's： | 8 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
The MAX3100 X1 input can be driven directly by an
external CMOS clock source. The trip level is approxi-
mately equal to VCC / 2. No connection should be made
to X2 in this mode. If a TTL or non-CMOS clock source
is used, AC couple with a 10nF capacitor to X1. The
peak-to-peak swing on the input should be at least 2V
for reliable operation.
9-Bit Networks
The MAX3100 supports a common multidrop communi-
cation technique referred to as 9-bit mode. In this mode,
the parity bit is set to indicate a message that contains a
header with a destination address. The MAX3100 parity
mask can be set to generate interrupts for this condition.
Operating a network in this mode reduces the process-
ing overhead of all nodes by enabling the slave con-
trollers to ignore most message traffic. This can relieve
the remote processor to handle more useful tasks.
In 9-bit mode, the MAX3100 is set up with 8 bits plus
parity. The parity bit in all normal messages is clear, but
is set in an address-type message. The MAX3100 pari-
ty-interrupt mask is enabled to generate an interrupt on
high parity. When the master sends an address mes-
sage with the parity bit set, all MAX3100 nodes issue an
interrupt. All nodes then retrieve the received byte to
compare to their assigned address. Once addressed,
the node continues to process each received byte. If the
node was not addressed, it ignores all message traffic
until a new address is sent out by the master.
The parity/9th-bit interrupt is controlled only by the data
in the receive register, and is not affected by data in the
FIFO, so the most effective use of the parity/9th-bit
interrupt is with FIFO disabled. With the FIFO disabled,
received nonaddress words can be ignored and not
even read from the UART.
SIR IrDA Mode
The MAX3100’s IrDA mode can be used to communicate
with other IrDA SIR-compatible devices, or to reduce
power consumption in opto-isolated applications.
In IrDA mode, a bit period is shortened to 3/16 of a
baud period (1.6s at 115,200 baud) (Figure 9). A data
zero is transmitted as a pulse of light (TX pin = logic
low, RX pin = logic high).
In receive mode, the RX signal’s sampling is done
halfway into the transmission of a high level. The sam-
pling is done once, instead of three times, as in normal
mode. The MAX3100 ignores pulses shorter than
approximately 1/16 of the baud period. The IrDA device
that is communicating with the MAX3100 must be set to
transmit pulses at 3/16 of the baud period. For compati-
bility with other IrDA devices, set the format to 8-bit
data, one stop, no parity.
IrDA Module
The MAX3100 was optimized for direct optocoupler
drive, whereas IrDA modules contain inverting buffers.
Invert the RX and TX outputs as shown in Figure 10.
8051 Example: IrDA to RS-232 Converter
Figure 10 shows the MAX3100 with an 8051 C. This
circuit receives IrDA data and outputs standard RS-232
data. Although the 8051 contains an internal UART, it
does not support IrDA or high-speed communications.
The MAX3100 can easily interface to the 8051 to sup-
port these high-performance communications modes.
The 8051 does not have an SPI interface, so communi-
cation with the MAX3100 is accomplished with port pins
and a short software routine (Figure 12a).
The software routine polls the IRQ output to see if data
is available from the MAX3100 UART. It then shifts the
data out, using the 8051 port pins, and transmits it out
the RS-232 side through the MAX3221 driver. The 8051
simultaneously monitors its internal UART for incoming
communications from the RS-232 side, and transmits
this data out the IrDA side through the MAX3100. The
low-level routine (UTLK) is the core routine that sends
and receives data over the port pins to simulate an SPI
port on the 8051. This technique is useful for any 8051-
based MAX3100 port-pin-interfaced application.
SPI/MICROWIRE-Compatible
UART in QSOP-16
START
STOP
START
STOP
NORMAL
RX
UART FRAME
DATA BITS
01
1
00
0
NORMAL UART
TX
11
1
00
0
IrDA
RX
IrDA
TX
Figure 9. IrDA Timing
MAX3100
Maxim Integrated
15
MAX3100
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BT2-IX-F1 | CONVERTER MOD DC/DC 15V 75W |
| D38999/24WD18PA | CONN RCPT 18POS JAM NUT W/PINS |
| V24B36H150B2 | CONVERTER MOD DC/DC 36V 150W |
| V24B36H150B | CONVERTER MOD DC/DC 36V 150W |
| V24A28E500BG | CONVERTER MOD DC/DC 28V 500W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3100CPD+ | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3100EEE | 功能描述:UART 接口集成电路 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3100EEE+ | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3100EEE+T | 功能描述:UART 接口集成电路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3100EEE-C78277 | 制造商:Maxim Integrated Products 功能描述:SPI/MICROWIRE-COMPATIBLE UART IN A QSOP-16 P - Bulk |
发布紧急采购，3分钟左右您将得到回复。