参数资料
| 型号： | MAX3100EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/12页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX3100 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 接口，UART 至 SPI/Microwire |
| 已用 IC / 零件： | MAX3100 |
| 已供物品： | 板 |
MAX3100 Evaluation Kit
Detailed Description of Hardware
The MAX3100 EV kit uses the MAXQ2000-RAX as a
host μC to communicate with the MAX3100 through the
SPI interface. The μC converts received characters to a
seven-segment LED display. The μC also implements a
master I 2 C-compatible interface to communicate with
the on-board MAX6626 temperature sensor.
The EV kit has a MAX3232 RS-232 transceiver to facili-
tate communication with a PC.
The EV kit is designed as a DCE device. The J1 female
DB9 connector pin functions are shown in Figure 2. EV
kit TX line is connected to PC RX line. EV kit RX line is
connected to PC TX line. EV kit RTS line is connected to
PC CTS line. EV kit CTS line is connected to PC RTS line.
The data communication between the EV kit and the PC
only requires TX and RX lines.
The logic of the RTS line (J2, pin 4) on the EV kit is con-
trolled by the MAX3100’s RTS configuration bit. RTS = 1
sets the RTS line to logic 0. RTS = 0 sets the RTS line to
logic 1. The logic of the CTS line (J2, pin 5) on the EV
kit is controlled by the PC ’s hardware flow control
(MAX3100’s CTS = 0, D3 = On; MAX3100’s CTS = 1,
D3 = Off).
Figure 2. EV Kit J1 Female DB9 Connector Pin Functions
MAX3100 Baud Rate Generation
Bits B3–B0 in the MAX3100 write-configuration register
determine the baud-rate divisor (BRD), which divides
the X1 oscillator frequency. The MAX3100 internal oscil-
lator operates with either a 1.8432MHz or a 3.6864MHz
crystal, or is driven at X1 with a 45% to 55% duty-cycle
square wave. The MAX3100 IC data sheet shows BRDs
for given input codes, as well as the baud rate for
1.8432MHz and 3.684MHz crystals. The generator’s
clock is 16 times the baud rate.
On the EV kit board, a 3.684MHz crystal is installed. A
user can replace it with a 1.8432MHz crystal or remove
Y1 and apply an external square wave on the EXTERNAL
CLOCK pad.
A user should first set B3–B0 bits to the desired values
on SW6 and then press and release SW1 to configure
the MAX3100 BRD.
Hardware Reset
Press SW4 on the EV kit to reset the μC and the
MAX3100 to its initial power-on-reset (POR) state.
Jumper and Switch Settings
See Tables 1, 2, and 3 for a description of the EV kit
jumpers and switch settings.
_______________________________________________________________________________________
5
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3160EEVKIT+ | EVAL KIT FOR MAX3160E |
| MAX3161EEVKIT+ | EVAL KIT FOR MAX3161E |
| MAX31855EVKIT# | KIT EVAL FOR MAX31855 |
| MAX3223EEVKIT+ | EVALUATION KIT MAX3223 |
| MAX3397EEVKIT+ | KIT EVALUATION FOR MAX3397E |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3100EVKIT+ | 功能描述:界面开发工具 MAX3100 Eval Kit RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX3107EAG+ | 功能描述:UART 接口集成电路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3107EAG+T | 功能描述:UART 接口集成电路 SPI/I2C Compatible RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3107ETG/V+ | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX3107ETG/V+T | 功能描述:UART 接口集成电路 SPI/IC UART with 128-Word FIFOs and Internal Oscillator RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。