- 您现在的位置：买卖IC网 > PDF目录1938 > MAX3120EUA (Maxim Integrated Products)IC TXRX 3V IRDA IR 3V 8-UMAX PDF资料下载
参数资料
| 型号： | MAX3120EUA |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC TXRX 3V IRDA IR 3V 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | 红外（IRDA） |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 管件 |
MAX3120
Transmitter
The MAX3120’s IR transmitter consists of a high-power
MOS switch, capable of quickly switching 200mA with
less than 2
of on-resistance. Internal buffering keeps
the input capacitance of the TXD pin extremely low to
ease the input drive requirement. Connect an IR LED in
series with a current-setting resistor to select the appro-
priate IR output power (see the
Powering the IR LED
section). Note that the transmitter does not have an
automatic shutoff circuit, so pay special attention to com-
ponent power dissipation in high-duty-cycle transmit
schemes.
Applications Information
IR LED and PIN Photodiode Selection
The IrDA specification calls for an IR transmitter with a
peak wavelength between 850nm and 900nm. Within a
±15° half-cone-angle, the output intensity of the IR LED
must be between 40mW/sr and 500mW/sr. Outside a
±30° half-cone-angle, the output intensity of the IR LED
must fall below 40mW/sr. The optical rise and fall times
of the IR LED must be less than 600ns. Based on these
system requirements, the Hewlett Packard HSDL-4220
or the Temic TSHF5400 IR LEDs are two appropriate
choices.
Appropriate PIN photodiode selection is extremely
important to system performance. The PIN diode must
generate at least 200nA (minimum sensitivity of the
MAX3120) of current when aimed ±15° off-axis with an
incident irradiance of 4W/cm2. Use the following equa-
tion to determine if the Temic BPV22NF meets these
requirements:
The first term (4W/cm2) is the minimum guaranteed
irradiance in the ±15° angular range. The second term
(0.075cm2) is the effective sensitive area of the PIN
diode. The factor of 1.8 accounts for the efficiency
increase due to the spherical lens. The first 0.95 factor
normalizes the sensitivity to the 875nm wavelength,
while the second 0.95 factor adjusts for decreased
receiver efficiency at ±15° off-axis. The last term,
0.6A/W, is the sensitivity of the PIN diode. In this exam-
ple, the Temic BPV22NF is an appropriate selection.
The final important factor in selecting a PIN diode is
effective diode capacitance. It is important to keep this
capacitance below 70pF at 1.2V reverse bias. Higher
input capacitance can compromise system noise per-
formance by increasing the noise gain of the input tran-
simpedance amplifier.
Powering the IR LED
Set the current in the IR LED using an external resistor.
Consult the IR LED manufacturer’s data sheet to select
a forward current that will meet IrDA specifications dis-
cussed in the
IR LED and PIN Photodiode Selection
section. Look up the drop across the LED (VLED) and
the drop across the MAX3120 LED driver (see
Typical
Operating Characteristics - VLEDC) and choose the cur-
rent-setting resistor based on the following equation:
Using the Hewlett Packard HSDL-4220 IR LED as an
example, VCC = 5V, ISET = 100mA, and VLED = 1.67V,
therefore:
VLEDC = 0.08V
RSET = 32.5
R=
V- V
- V
I
SET
CC
LED
LEDC
SET
IPIN =
=
(4 W/cm )(0.075cm )(1.8)(0.95) (0.6A/W)
291nA
22
2
Low-Profile, 3V, 120A,
IrDA Infrared Transceiver
6
_______________________________________________________________________________________
Figure 1. Functional Diagram
MAX3120
BIAS
BANDPASS
FILTER
SHDN
VCC
RXD
TXD
LEDC
PGND
PINC
1.2V
+
-
GND
相关PDF资料 |
PDF描述 |
|---|---|
| MAX312ESE | IC SWITCH QUAD SPST 16SOIC |
| MAX312LEUE+ | IC SWITCH QUAD SPST 16TSSOP |
| MAX3131EAI | IC TXRX RS2332 IRDA IR 28-SSOP |
| MAX313FEPE+ | IC SWITCH QUAD SPST 16DIP |
| MAX3140EEI+ | IC UART W/RS485 28-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3120EUA+ | 功能描述:接口 - 专用 3V 120uA IrDA Infrared Tcvr RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MAX3120EUA+T | 功能描述:接口 - 专用 3V 120uA IrDA Infrared Tcvr RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MAX3120EUA-T | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MAX312C/D | 功能描述:模拟开关 IC 10Ohm Quad SPST CMOS Analog Switches RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX312CAE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。