- 您现在的位置：买卖IC网 > PDF目录1938 > MAX3131EAI (Maxim Integrated Products)IC TXRX RS2332 IRDA IR 28-SSOP PDF资料下载
参数资料
| 型号： | MAX3131EAI |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/16页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS2332 IRDA IR 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 规程： | RS232 |
| 电源电压： | 3 V ~ 5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
MAX3130/MAX3131
3V to 5.5V, IrDA Infrared Transceiver with
Integrated RS-232 Interface
8
_______________________________________________________________________________________
Detailed Description
The MAX3130/MAX3131 are IrDA 1.2 compatible,
infrared transceivers with an integrated RS-232 inter-
face. By selecting appropriate external optical compo-
nents, these devices support IrDA 1.2 data rates from
2.4kbps to 115kbps at distances from 1cm to 1m. A
low-noise design allows them to achieve a bit-error rate
below 10-8 at maximum data rates. On-chip filtering
rejects out-of-band ambient light signals that interfere
with infrared communication. Both devices include a
high-power LED driver capable of sinking 200mA.
The MAX3130 and MAX3131 contain two RS-232 drivers
and two RS-232 receivers that support data rates up to
120kbps. The RS-232 transceiver is powered by a high-
efficiency, dual charge-pump power supply that oper-
ates with input supply voltages from +3.0V to +5.5V.
The MAX3130 is optimized for applications using a sin-
gle UART for both infrared and RS-232 communication.
The infrared transmitter input and infrared receiver out-
put are multiplexed with one RS-232 transmitter input
and one RS-232 receiver output, respectively. The
MAX3131 IrDA and RS-232 transceivers are indepen-
dent of each other for use in simultaneous multiprotocol
transceiver applications.
IR Receivers
The receiver amplifier reverse biases the PIN diode
with approximately 1.2V, and the PIN diode converts
pulses of IR light into pulses of current. The input trans-
impedance (current-to-voltage) amplifier converts and
amplifies these current pulses into voltage pulses. The
MAX3130/MAX3131 incorporate filters that remove low-
frequency ambient light interference and high-frequency
circuit noise from these voltage pulses. A high-speed
comparator then translates these voltage pulses into
CMOS output levels. Figures 1 and 2 show system
functional diagrams.
The RXD pin is the output of the infrared receiver for
the MAX3131. The R2OUT pin is the output of the
infrared receiver for the MAX3130 (IRMODE = low).
With the ENDEC disabled, the infrared receiver output
pulses low upon each incoming infrared pulse. The
pulse width of the receiver output depends on many
factors, including transmitter distance and power, PIN
photodiode efficiency and area, and incoming data
rate. Under all circumstances the output pulse is less
than one baud period. To communicate with UARTs
that are not IrDA compatible, enable the ENDEC (see
the
IrDA Encoder/Decoder (ENDEC) section).
MAX3131 Operational Modes Table
RSSD
IRSD
T_OUT
R_IN
LEDC
RXD
0
High-Z
Enabled
Logic High
0
1
High-Z
Enabled
IrDA Output
1
0
Enabled
Logic High
1
Enabled
IrDA Output
MAX3130 Function Table
RSSD
X
0
IRMODE
MAX3130
CONTROL INPUTS
IRSD
0
1
RS-232
Input
RS-232
Input
T1IN
LOGIC INPUTS
IrDA
Input
IrDA
Input
T2IN
Enabled
High-Z
T1OUT
RS-232 I/O
High-Z
T2OUT
Disabled
RS-232
Input
RS-232
Input
R1IN
PINC
RS-232
Input
RS-232
Input
R2IN
IrDA
INPUT
RS-232
Output
RS-232
Output
R1OUT
LOGIC OUTPUTS
IrDA
Output
IrDA
Output
R2OUT
Disabled
Enabled
LEDC
IrDA
OUTPUT
0
1
0
RS-232
Input
RS-232
Input
High-Z
RS-232
Input
RS-232
Input
RS-232
Output
RS-232
Output
Disabled
0
1
RS-232
Input
RS-232
Input
High-Z
RS-232
Input
RS-232
Input
RS-232
Output
RS-232
Output
Disabled
Enabled
Disabled
Enabled
1
0
RS-232
Input
RS-232
Input
RS-232
Output
RS-232
Output
RS-232
Input
RS-232
Input
RS-232
Output
RS-232
Output
Disabled
1
RS-232
Input
RS-232
Input
RS-232
Output
RS-232
Output
RS-232
Input
RS-232
Input
RS-232
Output
RS-232
Output
Disabled
X = Don’t care
相关PDF资料 |
PDF描述 |
|---|---|
| MAX313FEPE+ | IC SWITCH QUAD SPST 16DIP |
| MAX3140EEI+ | IC UART W/RS485 28-QSOP |
| MAX3157CAI | IC TXRX RS485/422 250KBPS 28SSOP |
| MAX3160CAP | IC TXRX RS485/422 10MBPS 20SSOP |
| MAX3160EEAP+T | IC TXRX RS232/485/422 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3131EAI+ | 功能描述:RS-232接口集成电路 3-5.5V IrDA Infrared Tcvr w/RS-232 Int RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX3131EAI+T | 功能描述:RS-232接口集成电路 3-5.5V IrDA Infrared Tcvr w/RS-232 Int RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX3131EAI-T | 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX313C/D | 功能描述:模拟开关 IC 10Ohm Quad SPST CMOS Analog Switches RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX313CPE | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。