- 您现在的位置：买卖IC网 > PDF目录1938 > MAX3160EEAP+T (Maxim Integrated Products)IC TXRX RS232/485/422 20SSOP PDF资料下载
参数资料
| 型号： | MAX3160EEAP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/26页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS232/485/422 20SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 规程： | RS232，RS422，RS485 |
| 电源电压： | 3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
MAX3160E/MAX3161E/MAX3162E
±15kV ESD-Protected, +3.0V to +5.5V, 10nA,
RS-232/RS-485/RS-422 Multiprotocol Transceivers
18
______________________________________________________________________________________
RS-232 Transmitter Outputs
when Exiting Shutdown
Figure 12 shows two transmitter outputs when exiting
shutdown mode. As they become active, the two trans-
mitter outputs are shown going to opposite RS-232 lev-
els (one transmitter input is high, the other is low). Each
transmitter is loaded with 3k
in parallel with 1000pF.
The transmitter outputs display no ringing or undesir-
able transients as they come out of shutdown. Note that
the transmitters are enabled only when V- exceeds
approximately -3V.
High Data Rates
The MAX3160E/MAX3161E/MAX3162E maintain the
RS-232 ±5V required minimum transmitter output voltage
even at high data rates. Figure 14 shows a transmitter
loopback test circuit. Figure 15 shows a loopback test
result at 250kbps, and Figure 16 shows the same test at
1Mbps. Figure 15 demonstrates a single slew-rate limit-
ed transmitter driven at 250kbps (FAST = GND) into an
RS-232 load in parallel with 1000pF. Figure 17 shows a
single transmitter driven at 1Mbps (FAST asserted),
loaded with an RS-232 receiver in parallel with 1000pF.
These transceivers maintain the RS-232 ±5V minimum
transmitter output voltage at data rates up to 1Mbps.
256 Transceivers on the Bus
The standard RS-485 receiver input impedance is 12k
(one-unit load), and the standard driver can drive up to
32-unit loads. The MAX3160E has a 1/4-unit load
receiver input impedance (48k
), allowing up to 128
transceivers to be connected in parallel on one com-
munication line. The MAX3161E/MAX3162E have a 1/8-
unit load receiver input impedance (96k
), allowing up
to 256 transceivers to be connected in parallel on one
communication line. Any combination of these devices
and/or other RS-485 transceivers with a total of 32-unit
loads or fewer can be connected to the line.
RS-485/RS-422
Driver Output Protection
Two mechanisms prevent excessive output current and
power dissipation caused by faults or by bus con-
tention. The first, a foldback current limit on the output
stage, provides immediate protection against short cir-
cuits over the whole common-mode voltage range (see
the Typical Operating Characteristics). The second, a
thermal shutdown circuit, forces the driver outputs into
a high-impedance state if the die temperature becomes
excessive, typically over +150°C.
Protection Against Wiring Faults
EIA/TIA-485 standards require a common input voltage
range of -7V to +12V to prevent damage to the device.
The MAX3160E/MAX3161E/MAX3162E inputs are pro-
tected to RS-232 levels of ±25V for the receiver inputs
and ±13V for the transmitter/driver outputs. This pro-
vides additional protection for the RS-485 transceivers
against ground differential or faults due to miswiring.
RS-485/RS-422 Reduced
EMI and Reflections
The MAX3160E/MAX3161E/MAX3162E can be config-
ured for slew-rate limiting by pulling FAST low. This mini-
mizes EMI and reduces reflections caused by improperly
terminated cables. Operation in slew-rate limited mode
reduces the amplitudes of high-frequency harmonics.
RS-485/RS-422 Line Length vs. Data
Length
The RS-485/RS-422 standard covers line lengths up to
4000ft. For line lengths greater than 4000ft, use the
repeater application shown in Figure 17.
RS-232/RS-485 Protocol Translator
Figure 18 shows the MAX3162E configured as an
RS-232/RS-485 protocol translator. The direction of
translation is controlled through the RTS signal (R1IN).
The single-ended RS-232 receiver input signal is trans-
lated to a differential RS-485 transmitter output.
Similarly, a differential RS-485 receiver input signal is
translated to a single-ended RS-232 transmitter output.
RS-232 data received on R2IN is transmitted as an RS-
485 signal on Z and Y. RS-485 signals received on A
and B are transmitted as an RS-232 signal on T1OUT.
MAX3160E
MAX3161E
MAX3162E
5k
R_ IN
R_ OUT
C2-
C2+
C1-
C1+
V-
V+
VCC
C4
C3
C1
C2
VCC
CBYPASS
SHDN
T_ OUT
T_ IN
GND
VCC
1000pF
Figure 14. Loopback Test Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3170CAI | IC TXRX CLOCK/DATA 3.3V 28-SSOP |
| MAX3171CAI | IC TXRX MULTIPROTOCL 3.3V 28SSOP |
| MAX3172CAI | IC TXRX MULTIPROTOCL 3.3V 28SSOP |
| MAX3175CAI+ | IC TXRX MULTIPROTOCOL 28-SSOP |
| MAX31782ETL+T | IC MICROCONTROLLER 40TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3160EEVKIT+ | 功能描述:界面开发工具 MAX3160E Eval Kit RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX3161CAG | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3161CAG+ | 功能描述:RS-422/RS-485 接口 IC 3-5.5V 1uA Tcvr Multiprotocol RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3161CAG+T | 功能描述:RS-422/RS-485 接口 IC 3-5.5V 1uA Tcvr Multiprotocol RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3161CAG-T | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。