参数资料
| 型号： | MAX3161EEVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/7页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX3161E |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 接口，数字线缆驱动器 |
| 已用 IC / 零件： | MAX3161 |
| 已供物品： | 板 |
MAX3161E Evaluation Kit
Quick Start
Recommended Equipment
receiver operate in full-duplex or half-duplex mode and
communicate at data rates up to 10Mbps. The
MAX3161E receiver represents a 1/8 unit load on the
?
?
?
3.3V, 0.5A DC power supply
Logic function generator
Oscilloscope
RS-485/RS-422 bus. Resistors R5 and R6 provide a
configurable termination for the RS-485/RS-422 bus.
Terminal block J2 eases connection to the RS-485/RS-
422 bus. The DB9 connector J1 is available for interfac-
Procedure
The MAX3161E EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed .
1) Verify that shunts are installed across pins 1-2 of
jumpers JU5–JU8 (data communications equipment
(DCE) mode).
2) Verify that a shunt is installed on jumpers JU3
(RS-232 mode) and JU4 (full-duplex mode).
3) Verify that shunts are not installed on jumpers JU1
(MAX3161E enabled), JU2 (fast mode), and JU9 and
JU10 (RS-485/RS-422 differential I/O not terminated).
4) Set the DC power-supply output to 3.3V and disable
the output.
5) Set the logic function generator to a 3.3V P-P ,
ing with an RS-232 serial line. See Table 5 and Figures
1, 2, and 3 for the respective signal pins or pads.
Jumper Selection
The MAX3161E EV kit utilizes several jumpers to reconfig-
ure circuit features and functionality: IC enable, slew-rate
selection, communication-protocol selection, full-duplex/
half-duplex communication, DTE/DCE connections, and
RS-485/RS-422 differential I/O termination.
Enable
The MAX3161E EV kit features jumper JU1 to enable the
MAX3161E or place the IC in shutdown mode, thus
reducing quiescent current. A SHDN PCB pad is also pro-
vided for the shutdown signal to interface with an external
controller. See Table 1 for configuring jumper JU1.
Table 1. MAX3161E Enable (Jumper JU1)
500kHz, 1.65V DC offset square wave and disable
the output. Terminate the function generator as
needed.
SHUNT
POSITION
SHDN PIN
EV KIT FUNCTION
6) Connect the DC power-supply positive output to the
Installed
Connected to GND MAX3161E shutdown
VCC pad on the EV kit.
7) Connect the supply ground to the GND pad next to
Not installed
Connected to VCC
through resistor R1
MAX3161E enabled
VCC on the EV kit.
8) Connect the logic function generator output to the
DI/T1IN PCB pad and connect ground to the GND
PCB pad.
9) Enable the power-supply output and then the func-
tion generator output.
10) Use the oscilloscope to measure the transmitter out-
put T1OUT at pin 3 of jumper JU5. Verify that the
waveform is a 500kHz square wave and is approxi-
mately ±5V P-P .
Slew-Rate Selection
Jumper JU2 on the EV kit configures the MAX3161E
communication slew-rate mode. Slew-rate limited-mode
operation minimizes EMI radiation, while fast-mode
operation optimizes maximum data rates for either pro-
tocol. See Table 2 for configuring jumper JU2 and refer
to the MAX3161E IC data sheet for more information on
slew-rate configuration.
Table 2. Slew Rate (Jumper JU2)
Detailed Description
The MAX3161E EV kit demonstrates the MAX3161E
RS-232/RS-485/RS-422 multiprotocol transceiver IC.
The EV kit operates from a 3V to 5.5VDC source capa-
ble of supplying 100mA.
The EV kit features jumpers to configure the communi-
cation protocol to RS-232 operation or RS-485/RS-422
operation. In RS-232 mode operation, the MAX3161E
communicates at data rates up to 1Mbps. In RS-485/
RS-422 mode operation, the differential driver and
SHUNT
POSITION
Installed
Not installed
FAST PIN
Connected to
GND
Connected to
VCC through
resistor R2
EV KIT FUNCTION
Slew-rate limited mode.
RS-232/RS-485/RS-422
250kbps maximum data
rate
Fast mode. RS-232 1Mbps
maximum data rate;
RS-485/RS-422 10Mbps
maximum data rate
2
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX31855EVKIT# | KIT EVAL FOR MAX31855 |
| MAX3223EEVKIT+ | EVALUATION KIT MAX3223 |
| MAX3397EEVKIT+ | KIT EVALUATION FOR MAX3397E |
| MAX3420EEVKIT-2+ | EVAL KIT FOR MAX3420E |
| MAX34446EVKIT# | KIT EVAL FOR MAX34446 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3161EEVKIT+ | 功能描述:界面开发工具 MAX3161E Eval Kit RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX31629MTA+T | 制造商:Maxim Integrated Products 功能描述:I2C THERMOMETER & RTC TDFN TR - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC I2C THERMOMETER RTC TDFN |
| MAX3162CAI | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3162CAI+ | 功能描述:RS-422/RS-485 接口 IC 3-5.5V 1uA Tcvr Multiprotocol RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| MAX3162CAI+T | 功能描述:RS-422/RS-485 接口 IC 3-5.5V 1uA Tcvr Multiprotocol RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。