参数资料
型号: MAX3174CAI+T
厂商: Maxim Integrated Products
文件页数: 3/19页
文件大小: 0K
描述: IC TERM/TXRX MULTIPROT 28-SSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,000
类型: 收发器
驱动器/接收器数: 1/1
规程: RS232
电源电压: 3 V ~ 3.6 V
安装类型: 表面贴装
封装/外壳: 28-SSOP(0.209",5.30mm 宽)
供应商设备封装: 28-SSOP
包装: 带卷 (TR)
MAX3172/MAX3174
+3.3V Multiprotocol Software-Selectable
Cable Terminators and Transceivers
______________________________________________________________________________________
11
configured for V.10 or V.28 operation as a driver or
receiver (Table 3). This mode-selection table is compati-
ble for use with the MAX3170 (clock/data transceiver)
and the MAX3171/MAX3173 (control transceiver). For
example, if X.21 mode is selected in DCE mode (M2 = 0,
M1 = 1, M0 = 1, and DCE/DTE = 1), the MAX3170,
MAX3171/MAX3173, and MAX3172/MAX3174 trans-
ceivers will all be placed in X.21 DCE mode.
Fail-Safe
The MAX3172/MAX3174 guarantee a logic HIGH
receiver output when the receiver input is shorted to
GND or when it is connected to a terminated transmis-
sion line with the driver disabled. The V.10 receiver
threshold is between +25mV and +250mV. If the V.10
receiver input voltage is less than +25mV, R4OUT is
logic HIGH. If the V.10 receiver input is greater than
+250mV, R4OUT is logic LOW.
The V.28 receiver threshold is between +0.8V and
+2.0V. If the V.28 receiver input voltage is less than
+0.8V, R4OUT is logic HIGH. If the receiver input is
greater than +2.0V, R4OUT is logic LOW. If the driving
transmitter is disabled or disconnected, the receiver’s
input voltage is pulled to zero by its internal termination.
With the receiver thresholds of the MAX3172/MAX3174,
this results in a logic HIGH.
Applications Information
Older multiprotocol cable termination implementations
have been constructed using expensive relays with dis-
crete resistors, custom cables with built-in termination,
or complex circuit board configurations to route signals
to the correct termination. The MAX3172/MAX3174 pro-
vide a simple solution to this termination problem. All
required termination configurations are software selec-
table using four mode-control input pins (M2, M1, M0,
and DCE/DTE).
V.11 Termination
For high-speed data transmission, the V.11 specifica-
tion recommends terminating the cable at the receiver
100
MIN
A′
B′
C′
A
B
C
GENERATOR
BALANCED
INTERCONNECTING
CABLE
TERMINATION
RECEIVER
LOAD
Figure 6. Typical V.11 Interface
A
B
S2 OFF
V.11 MODE
V.35 MODE
HIGH-Z MODE
A
C*
B
S2 ON
S1 OFF
A
B
S2 OFF
C*
*NODE C IS PROVIDED IN NETWORKS 1,2,3.
R2
52
R1
52
S1 ON
R3
127
R2
52
R1
52
S1 ON
R3
127
R2
52
R1
52
R3
127
Figure 5. MAX3172/MAX3174 Termination Network Configurations
相关PDF资料
PDF描述
IDT74SSTU32864BFG8 IC BUFFER 1:1/1:2 96-LFBGA
MAX3172CAI+T IC TERM/TXRX MULTIPROT 28-SSOP
MS27499E18B32PA CONN RCPT 32POS BOX MNT W/PINS
VE-B43-MW-F4 CONVERTER MOD DC/DC 24V 100W
VE-B42-MW-F4 CONVERTER MOD DC/DC 15V 100W
相关代理商/技术参数
参数描述
MAX3175CAI 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装:
MAX3175CAI+ 功能描述:接口 - 专用 5V Multiprotocol RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59
MAX3175CAI+T 功能描述:接口 - 专用 5V Multiprotocol RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59
MAX3175CAI-T 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装:
MAX31760AEE+ 功能描述:马达/运动/点火控制器和驱动器 Fan Speed Controller w/LUT RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube