- 您现在的位置：买卖IC网 > PDF目录6009 > MAX3206EETC+ (Maxim Integrated Products)IC ESD PROT ARRAY 12-TQFN PDF资料下载
参数资料
| 型号： | MAX3206EETC+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/9页 |
| 文件大小： | 0K |
| 描述： | IC ESD PROT ARRAY 12-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 电极标记： | 6 通道阵列 - 单向 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-TQFN 裸露焊盘 |
| 供应商设备封装： | 12-TQFN |
| 包装： | 管件 |
Low-Capacitance, 2/3/4/6-Channel, ±15kV ESD
Protection Arrays for High-Speed Data Interfaces
The Air-Gap Discharge test involves approaching the
R C
50 ? to 100 ?
CHARGE-CURRENT-
LIMIT RESISTOR
R D
330 ?
DISCHARGE
RESISTANCE
device with a charged probe. The Contact Discharge
method connects the probe to the device before the
probe is energized.
Layout Recommendations
Proper circuit-board layout is critical to suppress ESD-
HIGH-
VOLTAGE
DC
SOURCE
Cs
150pF
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
induced line transients. The MAX3202E/MAX3203E/
MAX3204E/MAX3206E clamp to 100V; however, with
improper layout, the voltage spike at the device is
much higher. A lead inductance of 10nH with a 45A
current spike at a dv/dt of 1ns results in an ADDITION-
AL 450V spike on the protected line. It is essential that
the layout of the PC board follows these guidelines:
1) Minimize trace length between the connector or
Figure 6. IEC 61000-4-2 ESD Test Model
IEC 61000-4-2
The IEC 61000-4-2 standard covers ESD testing and
performance of finished equipment. The MAX3202E/
MAX3203E/MAX3204E/MAX3206E help users design
equipment that meets Level 4 of IEC 61000-4-2.
The main difference between tests done using the
Human Body Model and IEC 61000-4-2 is higher peak
current in IEC 61000-4-2. Because series resistance is
lower in the IEC 61000-4-2 ESD test model (Figure 6)
the ESD-withstand voltage measured to this standard is
generally lower than that measured using the Human
Body Model. Figure 3 shows the current waveform for
the ±8kV IEC 61000-4-2 Level 4 ESD Contact
Discharge test.
input terminal, I/O_, and the protected signal line.
2) Use separate planes for power and ground to reduce
parasitic inductance and to reduce the impedance to
the power rails for shunted ESD current.
3) Ensure short ESD transient return paths to GND
and V CC .
4) Minimize conductive power and ground loops.
5) Do not place critical signals near the edge of the
PC board.
6) Bypass V CC to GND with a low-ESR ceramic capac-
itor as close to V CC as possible.
7) Bypass the supply of the protected device to GND
with a low-ESR ceramic capacitor as close to the
supply pin as possible.
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| SSW-129-02-T-S | CONN RCPT .100" 29POS SNGL TIN |
| TMM-119-01-T-S-SM | CONN HEADER 19POS SNGL 2MM SMD |
| SSW-127-01-S-S | CONN RCPT .100" 27POS SNGL GOLD |
| PEC33SBBN | CONN HEADER .100 SINGL R/A 33POS |
| PBC29SABN | CONN HEADER .100 SINGL STR 29POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3206EETC+ | 功能描述:TVS二极管阵列 6Ch ESD Protection Array RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C |
| MAX3206EETC+T | 功能描述:TVS二极管阵列 6Ch ESD Protection Array RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C |
| MAX3206EETC-T | 功能描述:TVS二极管阵列 RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C |
| MAX3206EEWL+ | 制造商:Maxim Integrated Products 功能描述:LOW-CAPACITANCE 2/6-CHANNEL +/-15 - Rail/Tube |
| MAX3206EEWL+T | 功能描述:TVS二极管阵列 Low-Capacitance, 2/3 /4/6-Channel, +-15kV RoHS:否 制造商:Littelfuse 极性: 通道:4 Channels 击穿电压: 钳位电压:11.5 V 工作电压:2.5 V 峰值浪涌电流:20 A 安装风格:SMD/SMT 端接类型:SMD/SMT 系列: 最小工作温度:- 40 C 最大工作温度:+ 85 C |
发布紧急采购，3分钟左右您将得到回复。