- 您现在的位置：买卖IC网 > PDF目录1939 > MAX3302EETI+ (Maxim Integrated Products)IC USB TXRX OTG 28-TQFN-EP PDF资料下载
参数资料
| 型号： | MAX3302EETI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/38页 |
| 文件大小： | 0K |
| 描述： | IC USB TXRX OTG 28-TQFN-EP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 类型： | 收发器 |
| 规程： | USB 2.0 |
| 电源电压： | 3 V ~ 4.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
______________________________________________________________________________________
23
BIT NUMBER
SYMBOL
OPERATION
VALUE AT
POWER-UP
0
speed
Set to 0 for low-speed (1.5Mbps) mode. Set to 1 for full-speed (12Mbps) mode. This
bit changes the data rate only if spd_susp_ctl = 1 in special-function register 1.
0
1
suspend
Set to 0 for normal operating mode. Set to 1 for suspend mode. This bit changes
the operating mode only if spd_susp_ctl = 1 in special-function register 1.
0
2
dat_se0
Set to 0 for VP_VM USB mode. Set to 1 for DAT_SE0 USB mode.
0
3
—
Not used.
0
4
bdis_acon_en
Enables the transceiver (when configured as an A device) to connect its pullup
resistor if the B device disconnect is detected during HNP. Set to 0 to disable this
feature. Set to 1 to enable this feature.
0
5
oe_int_en
Set to 0 to disable the interrupt output circuitry of
OE/INT. Set to 1 to enable the
interrupt output circuitry of
OE/INT.
0
6
uart_en
Set to 0 to disable UART mode. Set to 1 to enable UART mode. This bit overrides
the settings of dminus_dir, dplus_dir, and gp_en bits.
0
7
—
Not used.
0
Table 7. Control Register 1 Description (Write to Address 04h to Set, Write to Address
05h to Clear)
BIT NUMBER
SYMBOL
OPERATION
VALUE AT
POWER-UP
0
dp_pullup
Set to 0 to disconnect the pullup resistor to D+. Set to 1 to connect the pullup resistor to D+.
0
1
dm_pullup
Set to 0 to disconnect the pullup resistor to D-. Set to 1 to connect the pullup resistor to D-.0
2
dp_pulldown
Set to 0 to disconnect the pulldown resistor to D+. Set to 1 to connect the pulldown
resistor to D+.
1
3
dm_pulldown
Set to 0 to disconnect the pulldown resistor to D-. Set to 1 to connect the pulldown
resistor to D-.
1
4
id_pulldown
Set to 0 to allow ID_IN to float. Set to 1 to connect ID_IN to GND.
0
5
vbus_drv
Set to 0 to turn VBUS off. Set to 1 to drive VBUS through a low impedance (see Note 8).0
6
vbus_dischrg
Set to 0 to disconnect the VBUS discharge resistor. Set to 1 to connect the VBUS
discharge resistor (see Note 8).
0
7
vbus_chrg
Set to 0 to disconnect the VBUS charge resistor. Set to 1 to connect the VBUS
charge resistor (see Note 8).
0
Table 8. Control Register 2 Description (Write to Address 06h to Set, Write to Address
07h to Clear)
Note 8: To prevent a high-current state where the transceiver is both sourcing current to VBUS and sinking current from VBUS, the fol-
lowing logic is used to set bits 5, 6, and 7 of control register 2:
Setting vbus_drv clears vbus_dischrg and vbus_chrg
Setting vbus_dischrg clears vbus_drv and vbus_chrg, unless vbus_drv is set with the same command, in which case vbus_drv
clears the other bits
Setting vbus_chrg clears vbus_drv and vbus_dischrg, unless either of these bits are set with the same command, as shown in Table 9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3311EEUB | IC TXRX RS232 460KBPS 10-UMAX |
| MAX3313EUB | IC TXRX RS232 460KBPS 10-UMAX |
| MAX3314EESA+ | IC TXRX RS232 460KBPS 8-SOIC |
| MAX3314EUA+T | IC TXRX RS232 460KBPS 8-UMAX |
| MAX3317EEAP+ | IC TXRX RS232 460KBPS 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3302EETI+ | 功能描述:USB 接口集成电路 USB On-the-Go Tcvr & Charge Pump RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| MAX3302EETI+T | 功能描述:USB 接口集成电路 USB On-the-Go Tcvr & Charge Pump RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| MAX3302EETJ+ | 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube |
| MAX3302EEWA+ | 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO TRANSCEIVERS AND CHARGE PUMPS - Rail/Tube |
| MAX3302EEWA+T | 功能描述:USB 接口集成电路 USB On-the-Go Tcvr & Charge Pump RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
发布紧急采购，3分钟左右您将得到回复。