- 您现在的位置：买卖IC网 > PDF目录9772 > MAX3325EAI+ (Maxim Integrated Products)IC TXRX DUAL RS232 LCD 28-SSOP PDF资料下载
参数资料
| 型号： | MAX3325EAI+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC TXRX DUAL RS232 LCD 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 规程： | RS232 |
| 电源电压： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
Applications Information
Capacitor Selection
The capacitor type used for C1–C4 is not critical for
proper operation; polarized or nonpolarized capacitors
can be used. Ceramic chip capacitors with an X7R
dielectric provide the best combination of performance,
cost, and size. The charge pump requires 0.22F
capacitors for 3.3V operation. Do not use values small-
er than those listed in Figure 1. Increasing the capacitor
values (e.g., by a factor of 2) reduces ripple on the
transmitter outputs, slightly reduces power consump-
tion, and increases the available output current from
VREG and VLCD. C2, C3, and C4 can be increased
without changing C1’s value. However, do not
increase C1 without also increasing the values of
C2, C3, C4, and C5 to maintain the proper ratios.
When using the minimum required capacitor values,
make sure the capacitor value does not degrade exces-
sively with temperature or voltage. This is typical of Y5V
and Z5U dielectric ceramic capacitors. If in doubt, use
capacitors with a larger nominal value, or specify X7R
dielectric. The capacitor’s equivalent series resistance
(ESR), which usually rises at low temperatures, influences
the amount of ripple on V+ and V-.
Power-Supply Decoupling
In most circumstances, a 0.22F VDD bypass capacitor
(C5) is adequate. Choosing larger values for C5
increases performance and decreases the induced rip-
ple on the VDD supply line. Note that capacitor C2, con-
nected to V+, is returned to C5. This connection also
improves the performance of the MAX3325. Locate all
bypass capacitors as close as possible to the IC. Keep
metal traces as wide as possible. Return all capacitor
ground connections directly to a solid-copper ground
plane.
Transmitter Outputs
when Exiting Shutdown
The
Typical Operating Characteristics show the
MAX3325 transmitter outputs when exiting shutdown
mode. As they become active, the two transmitter out-
puts are shown going to opposite RS-232 levels (one
transmitter input is high, the other is low). Each trans-
mitter is loaded with 3k
in parallel with 2500pF. The
transmitter outputs display no ringing or undesirable
transients as they come out of shutdown. Note that the
transmitters are enabled only when the magnitude of V-
exceeds approximately -3V.
High Data Rates
The MAX3325 maintains the RS-232 ±5.0V minimum
transmitter output voltage even at high data rates.
Figure 1 shows a transmitter loopback test circuit. The
Typical Operating Characteristics show loopback test
results at 120kbps and 250kbps. For 120kbps, all trans-
mitters were driven simultaneously at 120kbps into RS-
232 loads in parallel with 1000pF. For 250kbps, a single
transmitter was driven at 250kbps, and all transmitters
were loaded with an RS-232 receiver in parallel with
1000pF.
Interconnection with
Lower Logic Voltages
The MAX3325 provides a separate supply for the logic
interface to optimize input and output levels. Connect
VL to the system’s logic supply voltage, and bypass it
with a 0.1F capacitor to GND. If the logic supply is the
same as VDD, connect VL to VDD. The VL pin can be
operated from +1.8V to +5.0V to accommodate various
logic levels.
Setting VLCD Output Voltage
The LCD output can be configured in a variety of ways
to suit the requirements of the LCD display. First, deter-
mine the nominal voltage range that the LCD will
require for adequate contrast adjustment. If the display
requires temperature compensation for contrast,
include the TEMP output in all calculations. The output
voltage is defined by:
where code is the current digital code in the DAC, and
RO is the nominal DAC output impedance (50k
). The
other terms in the equation are due to external resis-
tances connected to the indicated pins. A spreadsheet
program is an excellent tool for helping to select compo-
nents and evaluate their effect on the output voltage
range.
Although the above equation has terms for both REF+
and REF- offset resistors, only one or the other is used.
Design Example
The first step in designing for a particular display is to
obtain the manufacturer’s device specifications for the
nominal values as well as the temperature characteristics.
For example, consider the Optrex DMC series of dot
matrix LCD modules. The manufacturer specifies a nomi-
nal contrast bias voltage of 6V at +25°C, where bias volt-
age is VREG - VLCD. The temperature coefficient needed
V
= -R
code
V
R
+ R
V
R
V
R
-3.3V - V
(T - 25 C)
R
LCD
FB
DAC
O
DAC
REF+
REF-
TEMP
()
++
+
°
MAX3325
3V Dual RS-232 Transceiver with
LCD Supply and Contrast Controller
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| VE-26N-IU-F3 | CONVERTER MOD DC/DC 18.5V 200W |
| VE-26N-IU-F2 | CONVERTER MOD DC/DC 18.5V 200W |
| MXL1535EEWI+T | IC TXRX RS485/422 28-SOIC |
| VE-26N-IU-F1 | CONVERTER MOD DC/DC 18.5V 200W |
| MAX251ESD+T | IC RS-232 DRVR RX 5V 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3325EAI+ | 功能描述:RS-232接口集成电路 3V Dual Tcvr w/LCD S&C Controller RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX3325EAI+T | 功能描述:RS-232接口集成电路 3V Dual Tcvr w/LCD S&C Controller RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX3325EAI-T | 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX3325ENI | 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| MAX332CPE | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。