- 您现在的位置：买卖IC网 > PDF目录1842 > MAX34441ETL+T (Maxim Integrated Products)IC PS MANAGER PMBUS 5CH 40TQFN PDF资料下载
参数资料
| 型号： | MAX34441ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 44/53页 |
| 文件大小： | 0K |
| 描述： | IC PS MANAGER PMBUS 5CH 40TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 应用： | 基站网络线路卡，服务器 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电流 - 电源： | 2.5mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 带卷 (TR) |
| 其它名称： | 90-34441+TTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
PMBus 5-Channel Power-Supply Manager
and Intelligent Fan Controller
MFR_TIME_COUNT (DDh)
The MFR_TIME_COUNT command returns the number of seconds the device has been operating since the last time
power was applied to the device, RST was toggled, or a soft reset occurred. The counter is a 32-bit value and cannot
be reset by the user.
MFR_MARGIN_CONFIG (E0h)
The MFR_MARGIN_CONFIG command configures the digital PWM outputs to margin the power supplies. The
MFR_MARGIN_CONFIG command is described in Table 30.
Power-supply margining is implemented using the PWM outputs. The PWM frequency is 62.5kHz. The device close-loop
controls the duty cycle to margin the power supply. The device provides 6 bits of duty-cycle resolution.
The device margins the power supplies when OPERATION is set to one of the margin states. Margining of the supplies
does not begin until all enabled power supplies have exceeded their programmed POWER_GOOD_ON levels. When
this happens, the PWM output is enabled and the seed value from MFR_MARGIN_CONFIG is loaded as the initial
PWM duty cycle. The device then averages eight samples of VOUT for a total time of 40ms. If the measured VOUT and
the target (set by either VOUT_MARGIN_HIGH or VOUT_MARGIN_LOW) differ by more than 1%, the PWM duty cycle is
adjusted by one step. The direction of the duty cycle adjustment is determined by the SLOPE bit in MFR_MARGIN_CONFIG.
All changes to the PWM are made after averaging eight samples of VOUT over a 40ms period.
The device is unable to successfully margin a power supply to the programmed target when the PWM duty cycle
reaches 0% or 100% and the target voltage has not been achieved. If this occurs, the device continues attempting to
margin the power supply and does the following:
1) Sets the NONE OF THE ABOVE bit in STATUS_BYTE.
2) Sets the NONE OF THE ABOVE and MFR bits in STATUS_WORD.
3) Sets the MARGIN_FAULT bit in STATUS_MFR_SPECIFIC.
4) Notifies the host through ALERT assertion (if enabled in MFR_MODE).
Also, the averaged VOUT after the PWM has initially been enabled with the seed value is compared to the target value.
If the programmed seed value causes VOUT to exceed the target, a MARGIN_FAULT is declared. For example, if the
target is VOUT_MARGIN_LOW and VOUT is less than VOUT_MARGIN_LOW after seeding, MARGIN_FAULT is set. In
response to this fault, the device continues margining the power supply and does the following:
1) Sets the NONE OF THE ABOVE bit in STATUS_BYTE.
2) Sets the NONE OF THE ABOVE and MFR bits in STATUS_WORD.
3) Sets the MARGIN_FAULT bit in STATUS_MFR_SPECIFIC.
4) Notifies the host through ALERT assertion (if enabled in MFR_MODE).
Table_30._MFR_MARGIN_CONFIG
44
BIT
15
14:6
5:0
BIT_NAME
SLOPE
0
SEED
MEANING
PWM duty cycle to resulting voltage relationship.
0 = Negative slope (increasing duty cycle results in a lower voltage).
1 = Positive slope (increasing duty cycle results in a higher voltage).
These bits always return a 0.
This 6-bit value is used as the initial PWM duty cycle (i.e., seed value) when the device
begins to margin a power supply either up or down.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3600CTL+ | IC LASER DVR PROJECTOR 40TQFN |
| MAX3643ETG+T | IC LASR DRVR 2.5GBPS 3.6V 24TQFN |
| MAX3646ETG+T | IC LSR DRVR 622MBPS 3.63V 24TQFN |
| MAX3656ETG+ | IC LASR DRVR 2.5GBPS 3.6V 24TQFN |
| MAX3668EHJ+T | IC LSR DRVR 622MBPS 3.63V 32TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX34441EVKIT# | 功能描述:电源管理IC开发工具 MAX34441 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX34446ETL+ | 功能描述:监控电路 PMBus Power Supply Data Logger RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX34446ETL+T | 功能描述:监控电路 PMBus Power Supply Data Logger RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX34446EVKIT# | 功能描述:监控电路 MAX34446 Eval Kit RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX3444EAPA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。