- 您现在的位置：买卖IC网 > PDF目录16705 > MAX34446ETL+T (Maxim Integrated Products)IC PS DATA LOGGER PMBUS 40TQFN PDF资料下载
参数资料
| 型号： | MAX34446ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/36页 |
| 文件大小： | 0K |
| 描述： | IC PS DATA LOGGER PMBUS 40TQFN |
| 标准包装： | 2,500 |
| 应用： | 基站网络线路卡，服务器 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电流 - 电源： | 3mA |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | * |
| 封装/外壳： | * |
| 供应商设备封装： | * |
| 包装： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
MAX34446
PMBus Power-Supply Data Logger
Interpreting Received
DIRECT Format Values
The host system uses the following equation to convert
the value received from the PMBus device—in this case,
the MAX34446—into a reading of volts, degrees Celsius,
or other units as appropriate:
X = (1/m) x (Y x 10 -R - b)
where X is the calculated, real world value in the appro-
priate units (V, N C, etc.); m is the slope coefficient; Y is
the 2-byte, two’s complement integer received from the
PMBus device; b is the offset; and R is the exponent.
Sending a DIRECT Format Value
To send a value, the host must use the below equation
to solve for Y:
Y = (mX + b) x 10 R
where Y is the 2-byte, two’s complement integer to be
sent to the unit; m is the slope coefficient; X is the real
world value, in units such as volts, to be converted for
transmission; b is the offset; and R is the exponent.
The following example demonstrates how the host can
send and retrieve values from the device.
If the host received a value of 0D89h on a READ_VOUT
command, this is equivalent to:
X = (1/1) x (0D89h x 10 -(-0) – 0) = 3465mV = 3.465V
with READ_VOUT (8Bh) coefficients m = 1, b = 0, and
R = 0 (see Table 3 ).
All voltage-related parameters of PMBus devices are
reported as positive values. It is up to the system to know
that a particular output is negative if that is of interest to
the system. All output voltage-related commands use
2 data bytes.
Maxim Integrated
Fault Management and Reporting
Faults are reported in the various status registers and,
if enabled with the MFR_FAULT_RESPONSE command,
faults can also be indicated on the associated FAULTn
output. See the individual command sections for more
details.
Faults and warnings that are latched in the status regis-
ters are cleared when any one of the following conditions
occurs:
? A CLEAR_FAULTS command is received.
? The RST pin is toggled low.
? Bias power to the device is removed and then reapplied.
The device responds to fault conditions accord-
ing to the manufacturer fault response command
(MFR_FAULT_RESPONSE). This command byte deter-
mines how the device should respond to each particular
fault.
Password Protection
The device can be password protected by using the
LOCK bit in the MFR_MODE command. Once the
device is locked, only certain PMBus commands can be
accessed with the serial port. See Table 1 for a complete
list. Commands that have password protection return all
ones (FFh) with the proper number of data bytes when
read. When the device is locked, only the PAGE and
MFR_SERIAL commands can be written; all other com-
mands that are written are ignored. When MFR_SERIAL
is written and the upper 4 bytes match the internally flash-
stored value, the device unlocks and remains unlocked
until the LOCK bit in MFR_MODE is activated once again.
The LOCKED status bit in STATUS_MFR_SPECIFIC is
always available to indicate whether the device is locked
or unlocked.
14
相关PDF资料 |
PDF描述 |
|---|---|
| GCC24DCAD | CONN EDGECARD 48POS R/A .100 SLD |
| VLF4012AT-150MR63 | INDUCTOR POWER 15UH .63A SMD |
| GMC13DRTN-S13 | CONN EDGECARD 26POS .100 EXTEND |
| GBC25DCAD | CONN EDGECARD 50POS R/A .100 SLD |
| ECC17DRYS | CONN EDGECARD 34POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX34446EVKIT# | 功能描述:监控电路 MAX34446 Eval Kit RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX3444EAPA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX3444EASA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX3444EASA+ | 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX3444EASA+T | 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。