参数资料
| 型号： | MAX34446EVKIT# |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/36页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX34446 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MAX34446 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
MAX34446
PMBus Power-Supply Data Logger
RESET COMPLETE AND ENABLE PIN HIGH
DISABLE WRITES TO MFR_NV_FAULT_LOG
IF FAULT_EN ≠ 0X, ASSERT FAULTn PIN
FORCE PGn PINS LOW ON ALL CHANNELS CONFIGURED TO MONITOR VOLTAGE
(OTHER PGn PINS ARE HIGH IMPEDANCE)
MEASURE THE VOLTAGE/CURRENT/TEMPERATURE
ON VOLTAGE CHANNELS, IS THE MEASURED VOLTAGE > POWER_GOOD_ON?
YES
NO
SET PGn PIN HIGH
AFTER MFR_PG_DELAY
IS THE MEASURED PARAMETER WITHIN FAULT LIMITS?
(ALSO INCLUDES WARNING LIMITS IF FAULT_EN = 11)
YES
DEASSERT THE FAULTn PIN
ENABLE WRITES TO MFR_NV_FAULT_LOG
REGULAR PARAMETER MONITORING BEGINS
Figure 1. PGn and FAULTn Output After a Channel is Enabled
NO
Fault Response When a Channel
is Enabled
Whenever a channel (voltage, current, or temperature)
is enabled (V DD cycle, or hardware or software reset,
or by PMBus command) the channel’s FAULTn signal is
asserted if the FAULT_EN bits in MFR_FAULT_RESPONSE
are set so that the device responds to a fault or warn-
ing. If enabled, the FAULTn pin is not released until all
measurements pass. Also, prior to being allowed to set
Maxim Integrated
a fault/warning status bit or write a nonvolatile fault log
when a fault/warning occurs, the channel must first pass
this particular fault or warning.
Figure 1 describes the steps that the MAX34446 takes
to monitor a channel after the channel is enabled.
Figure 2 explains how the MAX34446 responds after
a channel is enabled and as faults and warnings pass
and fail. Figure 2 shows a voltage channel and over-
voltage faults and warnings, but these same steps
apply to other monitored parameters as well.
16
相关PDF资料 |
PDF描述 |
|---|---|
| MAX34561EVKIT# | EVAL KIT DUAL E-FUSE 24-TQFN |
| MAX34565EVKIT# | KIT EVAL FOR MAX34565 |
| MAX367CWN | IC SIGNAL-LINE CIRC PROT 18-SOIC |
| MAX4080EVKIT+ | KIT EVAL FOR MAX4080 |
| MAX4208EVKIT+ | KIT EVAL FOR MAX4208 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX34446EVKIT# | 功能描述:监控电路 MAX34446 Eval Kit RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX3444EAPA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX3444EASA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX3444EASA+ | 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX3444EASA+T | 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。