- 您现在的位置：买卖IC网 > PDF目录18711 > MAX3540EVKIT+ (Maxim Integrated)KIT FOR MAX3540 DVB TUNER PDF资料下载
参数资料
| 型号： | MAX3540EVKIT+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 4/10页 |
| 文件大小： | 0K |
| 描述： | KIT FOR MAX3540 DVB TUNER |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 调谐器 |
| 频率： | 54MHz ~ 860MHz |
| 适用于相关产品： | MAX3540 |
| 已供物品： | 板 |
MAX3540 Evaluation Kit
Connections and Setup
This section provides a step-by-step guide to testing
the basic functionality of the EV kit in UHF mode.
Caution: Do not turn on DC power or RF signal gen-
erators until all connections are completed:
1) Verify that the JP1 and JP6 shunts are removed, the
JP2 shunt is installed, and JP11 and JP12 have
shunts across pins 1-2.
2) With its output disabled, set the DC power supply to
+3.3V. Connect the power supply to the +3.3V
(through an ammeter if desired) and GND1 termi-
nals on the EV kit. If available, set the current limit to
500mA.
3) With its output disabled, set the second DC power
supply to +5V. Connect the power supply to the
+5V (through an ammeter if desired) and GND1 ter-
minals on the EV kit. If available, set the current limit
to 100mA.
4) With its output disabled, set both outputs of the dual-
output DC power-supply voltages to +3V. Connect
one of the outputs to the TP1 terminal and connect
the other output to the IF_AGC terminal.
5) With its output disabled, set the RF signal generator
to a 55.25MHz frequency and a -80dBm power
level. Connect the output of the RF signal generator
to the SMA connector labeled RFIN on the evalua-
tion board.
6) Connect a 25-pin parallel cable between the PC’s
parallel port and the MAX3540 evaluation board.
7) Turn on the +3.3V V CC power supply, +5V V CC
power supply, and the +3V dual-output gain-control
power supply. The supply current from the +3.3V
V CC supply should read approximately 200mA. The
supply current from the +5V V CC supply should
read approximately 20mA. Be sure to adjust the
power supply to account for any voltage drop
across the ammeter.
8) Install and run the MAX3540 control software.
Software is available for download on the Maxim
website at www.maxim-ic.com/evkitsoftware.
9) Load the default register settings from the control
software by clicking Edit: Load Defaults.
10) Connect the SMA connector labeled IF_OUT on the
evaluation board to a spectrum analyzer or to an
oscilloscope.
11) Enable the RF signal generator’s output.
12) Set the center frequency of the RF spectrum analyz-
er to the IF frequency set on the control software.
Check the output.
Gain Adjustment Calculations
Add an additional 6dB to the voltage gain to account
for the 2:1 transformer on the output. Add another
3.96dB to the voltage gain to account for the minimum
loss pad (R11 and R10) on the input. When measuring
noise figure, account for 5.7dB power loss of the mini-
mum loss pad.
An anti-aliasing filter is provided on the IF output (C21,
C25–C29, C31, C35, L9, L11). The passband of this fil-
ter is 6MHz centered at the IF frequency of 44MHz, and
is designed for a 200 Ω termination. Anti-aliasing filter
requirements vary depending on application; the filter
architecture and component values are provided as
general guidelines only.
Layout Considerations
The MAX3540 EV kit serves as a guide for PCB layout.
Keep RF signal lines as short as possible to minimize
losses and radiation. Use controlled impedance on all
high-frequency traces. The exposed pad must be sol-
dered evenly to the board’s ground plane for proper
operation. Use abundant vias beneath the exposed
pad for maximum heat dissipation. Use abundant
ground vias between RF traces to minimize undesired
coupling.
To minimize coupling between different sections of the
IC, the ideal power-supply layout is a star configuration,
which has a large decoupling capacitor at the central
V CC node. The V CC traces branch out from this node,
with each trace going to separate V CC pins of the
MAX3540. Each V CC pin must have a bypass capacitor
with a low impedance to ground at the frequency of
interest. Do not share ground vias among multiple con-
nections to the PCB ground plane.
4
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX7044EVKIT-315 | EVAL KIT MAX7044 |
| 0622022040 | TOOL INSERTION 50POS 5ROWS |
| MAX2686LEVKIT# | EVAL KIT |
| MAX2674EVKIT+ | EVAL KIT MAX2674 |
| MAX2692EVKIT# | EVAL KIT MAX2692 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3540EVKIT# | 功能描述:射频开发工具 MAX3540 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX3540EVKIT+ | 功能描述:射频开发工具 MAX3540 Eval Kit RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| MAX3540ULM#DG42 | 功能描述:调谐器 RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX3540ULM#TDG42 | 功能描述:调谐器 RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
| MAX3540ULM+ | 功能描述:调谐器 RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度: |
发布紧急采购，3分钟左右您将得到回复。