- 您现在的位置：买卖IC网 > PDF目录20023 > MAX3600ACTL+ (Maxim Integrated)IC LASER DVR PROJECTOR 40TQFN PDF资料下载
参数资料
| 型号： | MAX3600ACTL+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/23页 |
| 文件大小： | 0K |
| 描述： | IC LASER DVR PROJECTOR 40TQFN |
| 标准包装： | 60 |
| 类型： | 激光二极管驱动器 |
| 通道数： | 4 |
| 电源电压： | 3.3V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（5x5） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
Laser Driver for Projectors
V CCA
V POR1
POWER-ON RESET
Power-On-Reset
The power-on reset monitors the supply voltages of
the circuit (Figure 15). It is recommended that V CC
be applied to the IC before V A1 to V A4 are applied as
shown in Figure 16. On power-down, it is recommended
V A1
V A2
V A3
V A4
V POR2
V POR2
V POR3
AND
AND
AND
AND
POR1
POR2
POR3
POR4
that V A1 to V A4 are powered down before V CC . Failure
to follow the sequencing recommendation can result
in device stress, but has not been observed to cause
immediate damage.
Design Procedure
Supply Filter
Element C A (see the Typical Operating Circuits ) is pres-
ent to reduce supply noise and provide a ground return
path for switched current. Select C A R 10 F F. C A can be
composed of two or three capacitors in parallel.
Use care to ensure V A3 does not exceed +9V at any
time, including power-on, as this can damage the ESD
V POR2
Figure 15. Power-On Reset
VOLTS
DATA AND CLOCK INPUTS
protection circuitry.
Compensation Network
Optional compensation elements R C and C C can be
used to compensate the inductive load of the laser
(Figure 17). The resulting filter reduces ringing and
increases the switching time of the laser driver. The best
values for R C and C C should be found by experimenta-
tion. Note that C C must be charged before light output
appears from the laser. If a compensation network is
V A_
V CC
t VCC_ON (0.1 μ s)
used, minimize inductance in the ground return.
Typical starting values:
R C ≈ R L to 2 x R L (R L = Laser Resistance)
C C ≈ 1/(2 G f VIDEO x R L )
Ringing of the green laser can be reduced with resistor
R D .
Figure 16. Power-Supply Sequencing
TIME
PCB Layout
Place the green laser as close to the laser driver as pos-
sible. The green laser typically has a small resistive com-
ponent and is more sensitive to inductance than other
laser connections. The green laser connection should
LASER
DRIVER
V A_
OUT_
R D
LASER
C A
+V A_
appear as a low-impedance transmission line. Use wide
traces located close to the ground plane for maximum
capacitance.
C C
R C
The connection from OUT2 to the laser should be as short
as possible, ideally < 1cm. The connection distance from
the laser cathode, across the ground plane, through the
Figure 17. Optional Compensation Components
18
filter capacitor, to V A2 , is ideally < 1cm.
相关PDF资料 |
PDF描述 |
|---|---|
| T86C155M035EBSS | CAP TANT 1.5UF 35V 20% 2312 |
| VE-JN4-CX-S | CONVERTER MOD DC/DC 48V 75W |
| GBM15DRAN | CONN EDGECARD 30POS R/A .156 SLD |
| VI-2TV-CX | CONVERTER MOD DC/DC 5.8V 75W |
| EMA40DTKN | CONN EDGECARD 80POS DIP .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3600ACTL+ | 功能描述:激光驱动器 Laser Driver For Projectors RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3600ACTL+T | 功能描述:激光驱动器 Laser Driver For Projectors RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3600AGTL/V+ | 功能描述:激光驱动器 Laser Driver for automotive RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3600AGTL/V+T | 功能描述:激光驱动器 RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3600CTL+ | 功能描述:激光驱动器 Laser Driver For Projectors RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。