参数资料
| 型号： | MAX3669EHJ+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 3/13页 |
| 文件大小： | 0K |
| 描述： | IC LASR DRVR 622MBPS 5.5V 32TQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 激光二极管驱动器（光纤） |
| 数据速率： | 622Mbps |
| 通道数： | 1 |
| 电源电压： | 3.14 V ~ 5.5 V |
| 电流 - 电源： | 40mA |
| 电流 - 调制： | 75mA |
| 电流 - 偏置： | 80mA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-TQFP |
| 供应商设备封装： | 32-TQFP（5x5） |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
MAX3669
+3.3V, 622Mbps SDH/SONET
Laser Driver with Current Monitors and APC
AC ELECTRICAL CHARACTERISTICS
(V CC = +3.14V to +5.5V, load as shown in Figure 2, T A = -40°C to +85°C, unless otherwise noted. Typical values are at V CC = +3.3V,
T A = +25°C.) (Note 5)
PARAMETER
Modulation Current Range
SYMBOL
I MOD
(Note 6)
CONDITIONS
MIN
5
TYP
MAX
75
UNITS
mA
Modulation Off-Current
ENABLE = low (Note 2)
200
μA
Modulation Current Stability
Modulation Current Absolute
Accuracy
I MOD = 75mA
I MOD = 5mA (Note 4)
-620
-15
-165
205
+620
+15
ppm/°C
%
Output Rise/Fall Time
t R, t F
20% to 80%,
R L = 10 Ω | | 20 Ω load
I MOD = 5mA
I MOD = 75mA
100
230
200
375
ps
Jitter Generation (Peak-to-Peak)
(Note 7)
100
ps
Pulse-Width Distortion
(Peak-to-Peak)
Enable/Start-Up Delay
Maximum Consecutive Identical
Digits at 622Mbps
CID
(Notes 8, 9)
Open loop
I MOD = 5mA
I MOD = 75mA
80
70
10
250
155
135
ps
ns
Bits
Note 1: Tested with R MODSET = 5.11k Ω (I MOD ≈ 38mA), R BIASMAX = 4.56k Ω (I BIAS ≈ 52mA), excluding I BIAS and I MOD .
Note 2: Both the bias and modulation currents will be disabled if any of the current set pins are shorted to ground.
Note 3: Guaranteed by design and characterization. This assumes that the laser to monitor diode transfer function does not change
with temperature.
Note 4: See the Typical Operating Characteristics for worst-case distributions.
Note 5: AC characteristics are guaranteed by design and characterization.
Note 6: Total I MOD out of OUT+. See the Design Procedure section for information regarding current delivered to the laser.
Note 7: Input signal is a 622Mbps, 2 13 - 1 PRBS with eighty inserted 0s.
Note 8: Input signal is a 622Mbps, 11110000 pattern.
Note 9: PWD = (wider pulse – narrower pulse) / 2.
V CC
DATA+
DATA-
(DATA+) - (DATA-)
100mV MIN
800mV MAX
200mV P-P
MIN
OUT-
20 Ω
1 μ F
10 Ω
1600mV P-P
MAX
MAX3669
20 Ω
1 μ F
OSCILLOSCOPE
I OUT +
OUT+
I MOD
BIAS
I OUT+
12.4 Ω
50 Ω
15 Ω
V CC
Figure 1. Required Input Signal and Output Polarity
Maxim Integrated
Figure 2. Output Termination for Characterization
3
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3735AETG+T | IC LSR DRVR 2.7GBPS 3.63V 24TQFN |
| MAX3736ETE+ | IC LSR DRVR 3.2GBPS 3.63V 16TQFN |
| MAX3737ETJ+T | IC LSR DRVR 2.7GBPS 3.63V 32TQFN |
| MAX3738ETG+T | IC LASER DRIVER 4.25GBPS 24TQFN |
| MAX3740AETG+ | IC DRIVER SFP VCSEL 24-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3669ETG | 功能描述:激光驱动器 RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3669ETG+ | 功能描述:激光驱动器 3.3V 622Mbps SDH/SONET RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3669ETG+T | 功能描述:激光驱动器 3.3V 622Mbps SDH/SONET RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3669ETGEVKIT | 功能描述:激光驱动器 Evaluation Kit for the MAX3669ETG RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
| MAX3669ETG-T | 功能描述:激光驱动器 RoHS:否 制造商:Micrel 数据速率:4.25 Gbps 工作电源电压:3 V to 3.6 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:QFN-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。