- 您现在的位置：买卖IC网 > PDF目录1940 > MAX3800UTJ+ (Maxim Integrated Products)IC EQUALIZER DRVR 3.2GBPS 32TQFN PDF资料下载
参数资料
| 型号： | MAX3800UTJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/13页 |
| 文件大小： | 0K |
| 描述： | IC EQUALIZER DRVR 3.2GBPS 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 类型： | 驱动器 |
| 驱动器/接收器数： | 1/0 |
| 电源电压： | 3.14 V ~ 3.46 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 管件 |
MAX3800
CML, see Maxim application note HFAN-1.0, Interfacing
Between CML, PECL, and LVDS.
Flat Response and Skin-Effect
Compensation Amplifiers
The buffered input waveform is fed equally to two
amplifiers—the flat response amplifier and the skin-
effect compensation amplifier. The flat response ampli-
fier has a constant gain over the entire frequency range
of the device, and the skin-effect compensation amplifi-
er has a gain characteristic that approximates the
inverse of the skin-effect attenuation inherent in copper
cable. The skin-effect attenuation, in dB per unit length,
is proportional to the square root of the frequency. The
output currents from the two amplifiers are supplied to
the current-steering network. Note that when LOS
asserts low, equalization is minimized.
Current-Steering Network
The function of the current-steering network is to com-
bine adjustable quantities of the output currents from
the flat response and skin-effect compensation ampli-
fiers to achieve a desired current ratio. The ratio adjust-
ment is controlled by the dual power-detector feedback
loop.
The current-steering network is implemented with a pair
of variable attenuators that feed into a current-summing
node. The variable attenuators are used to attenuate
the output currents of the flat response and skin-effect
compensation amplifiers under control of the dual
power-detector feedback loop. The outputs of the two
attenuators are combined at the summing node and
then fed to the output limiting amplifier and the feed-
back loop.
Dual Power-Detector Feedback Loop
The output of the current-steering network is applied to
the inputs of two frequency-specific power detectors.
One of the power detectors is tuned to 200MHz and the
other is tuned to 600MHz. The outputs of the two power
detectors are applied to the inverting (200MHz power
detector) and noninverting (600MHz power detector)
inputs of the differential loop amplifier. The differential
outputs of the loop amplifier control the variable attenu-
ators in the current-steering network.
Output Limiting Amplifier
The output limiting amplifier amplifies the signal from
the current-steering network to achieve the specified
output voltage swing.
Applications Information
Refer to Maxim application note HFDN-10.0, Equalizing
Gigabit Copper Cable Links with the MAX3800 (avail-
able at www.maxim-ic.com) for additional applications
information.
Selecting RMOD
The cable driver output amplitude can be adjusted by
connecting a resistor with a value from 10k
to 20k
between the RMOD pin and ground. The exact output
amplitude of the driver for a given value of RMOD resis-
tance is dependent on a number of factors. Refer to the
Typical Operating Characteristics “Cable Driver Output
Voltage vs. RMOD” for typical values.
Cable Integrity Monitor (CIM)
The differential CIM output current is directly propor-
tional to the output current of the loop amplifier (which
controls the current-steering network—see Detailed
Description). This is an analog current output that indi-
cates the amount of equalization that is being applied.
A convenient way to monitor the CIM current is to con-
nect a 100k
resistor from each of the CIM outputs to
ground, and then measure the voltage at the CIM pins.
The amount of equalization (and thus the CIM output
level) is affected by various factors, including cable
type, cable length, signal bandwidth, etc. Refer to the
Typical Operating Characteristics “CIM Voltage vs.
Cable Length” for typical values under specific condi-
tions.
Loss-of-Signal (
L
LO
OS
S) Output
Loss-of-signal is indicated by the LOS output. A low
level on LOS indicates that the equalizer input signal
power has dropped below a threshold. The LOS output
indicates a loss of signal. When the equalizer no longer
detects a signal from the channel, the LOS output goes
low. When there is sufficient input voltage to the chan-
nel (typically greater that 650mV), LOS is high. The LOS
output is suitable for indicating problems with the trans-
mission link caused by, for example, a broken cable, a
defective driver, or a lost connection to the equalizer.
3.2Gbps Adaptive Equalizer
and Cable Driver
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3802UTK+TD | IC EQUALIZE CABLE 3.2GBPS 68TQFN |
| MAX3804ETE#TG16 | IC EQUALIZER REC 12.5GBPS 16TQFN |
| MAX3805ETE#TG16 | IC EQUALIZER REC 10.7GBPS 16TQFN |
| MAX3806GTC+T | IC AMP TRANSIMPEDANCE 12TQFN |
| MAX3812USA+T | IC DRIVER CABLE SD/HD 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3800UTJ+ | 功能描述:IC EQUALIZER DRVR 3.2GBPS 32TQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,240 系列:GD 类型:收发器 驱动器/接收器数:3/5 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:20-DIP（0.300"，7.62mm） 供应商设备封装:20-PDIP 包装:管件 |
| MAX3800UTJ+T | 功能描述:IC EQUALIZER DRVR 3.2GBPS 32TQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,240 系列:GD 类型:收发器 驱动器/接收器数:3/5 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:20-DIP（0.300"，7.62mm） 供应商设备封装:20-PDIP 包装:管件 |
| MAX3801EVKIT | 制造商:Maxim Integrated Products 功能描述:3.2GBPS ADAPTIVE EQUALIZER - Bulk |
| MAX3801EVKIT+ | 制造商:Maxim Integrated Products 功能描述:3.2GBPS ADAPTIVE EQUALIZER - Bulk |
| MAX3801UGG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。