- 您现在的位置：买卖IC网 > PDF目录1940 > MAX3806GTC+T (Maxim Integrated Products)IC AMP TRANSIMPEDANCE 12TQFN PDF资料下载
参数资料
| 型号： | MAX3806GTC+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC AMP TRANSIMPEDANCE 12TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 距离测量，前置放大器 |
| 输入类型： | 逻辑 |
| 输出类型： | 电压 |
| 电流 - 电源： | 15mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-TQFN 裸露焊盘 |
| 供应商设备封装： | 12-TQFN EP（3x3） |
| 包装： | 带卷 (TR) |
MAX3806
Receiver for Optical Distance Measurement
_______________________________________________________________________________________
7
Detailed Description
The MAX3806 preamplifier consists of a selectable-gain
transimpedance amplifier, a selectable 14dB attenuator,
and an output-driver block. The selectable-gain transim-
pedance amplifier linearly boosts the signal from the
photodiode. This block is followed by an attenuator
block that allows the user to attenuate the signal by
14dB selected by the ATT pin. The final block is the out-
put driver that can be disabled by asserting the DIS pin.
Transimpedance Amplifier
The selectable-gain transimpedance amplifier is con-
trolled by the GAIN pin. See Table 1 for gain settings.
Attenuator
The attenuator block can be set to pass the signal
through to the output stage with 0dB of attenuation
(ATT forced low) or with 14dB of attenuation (ATT
forced high).
Output Driver
The output driver is designed to drive an AC-coupled
load with an impedance of 2k
Ω or greater. The output
can be disabled by asserting the DIS pin high. When
the output is disabled, the OUT pin goes to a high-
impedance state. See Figure 1 for the equivalent output
circuit.
WARNING: The output is designed to be AC-coupled
to a high-impedance load. Operating the part with its
output DC-coupled to GND through a 2k
Ω or less load
may damage the output.
Applications Information
Settling Time
Settling time is the required time for the output to
achieve the final steady-state or AC amplitude swing
after a setting has been changed on the MAX3806. The
output common-mode voltage shifts when a change is
Pin Description
PIN
NAME
FUNCTION
1, 12
VCC
5V Power-Supply Connection
2
IN
Amplifier Input. Accepts AC-coupled photodiode input current.
3, 4
GND
Supply Ground
5
ATT
CMOS/TTL Input. Assert this pin high to enable a 14dB attenuator in the amplifier. Force this pin low
to disable the attenuator. Contains internal 40k
pulldown resistor. Connect to GND if not used.
6, 8, 11
N.C.
Not Connected. This pin is not internally connected.
7
GAIN
CMOS/TTL Input. Selects amplifier gain setting. Force high for 60k . Force low for 30k . Contains
internal 40k
pulldown resistor.
9
OUT
Amplifier Output. An increase in current into the IN pin causes the voltage at the OUT pin to decrease.
OUT must be AC-coupled to a load of 2k
or greater.
10
DIS
CMOS/TTL Input. Force high to disable the output of the MAX3806. Force low to enable the output.
Contains internal 60k
pullup resistor.
—
EP
Exposed Pad. The exposed pad must be soldered to circuit board ground for proper thermal and
electrical performance.
Table 1. Transimpedance Gain Settings
GAIN
TRANSIMPEDANCE (k )
LINEAR RANGE (μAP)
BANDWIDTH (MHz)
0
30
IIN
40
98
1
60
IIN
20
49
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3812USA+T | IC DRIVER CABLE SD/HD 8-SOIC |
| MAX3814CHJ+T | IC DRVR/EQUALIZER CABLE 32-TQFP |
| MAX3840ETJ+T | IC SW CROSSPOINT DL 32-TQFN |
| MAX3841ETG+T | IC SW CROSSPOINT 2X2 24-TQFN |
| MAX385ESE+T | IC SWITCH DUAL DPST 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX3812EVKIT | 功能描述:其他开发工具 RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压: |
| MAX3812EVKIT+ | 功能描述:其他开发工具 RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压: |
| MAX3812USA | 功能描述:缓冲器和线路驱动器 RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MAX3812USA+ | 功能描述:缓冲器和线路驱动器 Integrated Circuits (ICs) RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| MAX3812USA+T | 功能描述:缓冲器和线路驱动器 Integrated Circuits (ICs) RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。