参数资料
型号: MAX3983UGK+TD
厂商: Maxim Integrated Products
文件页数: 5/17页
文件大小: 0K
描述: IC SIGNAL COND QUAD 68-QFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
类型: 信号调节器
输入类型: CML
输出类型: CML
接口: LVTTL
电流 - 电源: 495mA
安装类型: 表面贴装
封装/外壳: 68-VFQFN 裸露焊盘
供应商设备封装: 68-QFN 裸露焊盘(10x10)
包装: 带卷 (TR)
MAX3983 will produce excessive crosstalk in InfiniBand
and CX4 cable assemblies.
Crosstalk
For InfiniBand and 10Gbase-CX4 applications, it is
imperative to know the near-end crosstalk characteristics
of the cable assemblies. 10Gbase-CX4 has defined the
upper limit over frequency for near-end crosstalk (NEXT)
with single and multiple aggressors. InfiniBand has only
specified a percentage as measured in the time domain
relative to the transmitter output. Regardless of the spec-
ification method, NEXT is a critical component of the link
performance. When using larger amounts of preempha-
sis, the received eye height is small and vulnerable to
NEXT. For those situations requiring a large transmit pre-
emphasis, the NEXT should be less than -30dB at fre-
quencies from 1GHz to 3GHz. It should be noted that
cables that meet the 10Gbase-CX4 NEXT and MDNEXT
should provide adequate isolation.
Layout Considerations
Circuit board layout and design can significantly affect
the performance of the MAX3983. Use good high-fre-
quency design techniques, including minimizing
ground inductance and using controlled-impedance
transmission lines on the data signals. Power-supply
decoupling should also be placed as close to the VCC
pins as possible. There should be sufficient supply fil-
tering. Always connect all VCCs to a power plane. Take
care to isolate the input from the output signals to
reduce feedthrough. The performance of the equalizer
is optimized for lossy environments. For best results,
use board material with a dielectric tangential loss of
approximately 0.02 and 4-mil-wide transmission lines.
High-speed materials with tangential loss of less than
0.01 can be used, but require special care to reduce
near-end crosstalk in cable assemblies.
Exposed-Pad Package
The exposed-pad, 68-pin QFN package incorporates
features that provide a very low thermal resistance path
for heat removal from the IC. The pad is electrical
ground on the MAX3983 and must be soldered to the
circuit board for proper thermal and electrical perfor-
mance. For more information on exposed-pad pack-
ages, refer to Maxim Application Note HFAN-08.1:
Thermal Considerations of QFN and Other Exposed-
Paddle Packages.
Interface Schematics
MAX3983
Quad Copper-Cable Signal Conditioner
______________________________________________________________________________________
13
RX_IN[1:4]+
TX_IN[1:4]+
GND
50
Ω
50
Ω
RX_IN[1:4]-
TX_IN[1:4]-
5pF
VCCX - 1.5V
VCCX
Figure 6. RX_IN and TX_IN Equivalent Input Structure
RX_OUT[1:4]+
TX_OUT[1:4]+
GND
50
Ω
50
Ω
RX_OUT[1:4]-
TX_OUT[1:4]-
VCCX
Figure 7. RX_OUT and TX_OUT Equivalent Output Structure
相关PDF资料
PDF描述
MAX3984UTE+ IC PREMP DRIVER 1CH 16-TQFN
MAX399ESE IC MULTIPLEXER DUAL 4X1 16SOIC
MAX4051CSE-T IC MULTIPLEXER 8X1 16SOIC
MAX4066CSD IC SWITCH QUAD SPST 14SOIC
MAX4079CWG+ IC A/V BACKEND 24-SOIC
相关代理商/技术参数
参数描述
MAX3983UTK+D 制造商:Maxim Integrated Products 功能描述:#EMPTY - Rail/Tube
MAX3984EVKIT+ 功能描述:缓冲器和线路驱动器 Evaluation Kit for the MAX3984 RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel
MAX3984UTE+ 功能描述:均衡器 1-10Gbps Preemphasis Driver w/Receive EQ RoHS:否 制造商:Texas Instruments
MAX3984UTE+T 功能描述:IC PREMP DRIVER 1CH 16-TQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:1,240 系列:GD 类型:收发器 驱动器/接收器数:3/5 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:20-DIP(0.300",7.62mm) 供应商设备封装:20-PDIP 包装:管件
MAX3986EVKIT+ 制造商:Maxim Integrated Products 功能描述:EVAL KIT MAX3986 (1GBPS TO 10.3GBPS LINEAR EQUALIZER) - Boxed Product (Development Kits)