- 您现在的位置：买卖IC网 > PDF目录1940 > MAX4051CSE-T (Maxim Integrated Products)IC MULTIPLEXER 8X1 16SOIC PDF资料下载
参数资料
| 型号： | MAX4051CSE-T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/19页 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLEXER 8X1 16SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 多路复用器 |
| 电路： | 1 x 8:1 |
| 导通状态电阻： | 100 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 2 V ~ 16 V，±2.7 V ~ 8 V |
| 电流 - 电源： | 1µA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
MAX4051/A,
MAX4052/A,
MAX4053/A
V+ and GND power the internal logic and logic-level
translators, and set both the input and output logic lim-
its. The logic-level translators convert the logic levels
into switched V+ and V- signals to drive the gates of
the analog signals. This drive signal is the only connec-
tion between the logic supplies (and signals) and the
analog supplies. V+ and V- have ESD-protection
diodes to GND.
The logic-level thresholds are TTL/CMOS compatible
when V+ is +5V. As V+ rises, the threshold increases
slightly, so when V+ reaches +12V, the threshold is
about 3.1V; above the TTL-guaranteed high-level mini-
mum of 2.8V, but still compatible with CMOS outputs.
Bipolar Supplies
These devices operate with bipolar supplies between
±3.0V and ±8V. The V+ and V- supplies need not be
symmetrical, but their sum cannot exceed the absolute
maximum rating of +17V.
Single Supply
These devices operate from a single supply between
+3V and +16V when V- is connected to GND. All of the
bipolar precautions must be observed. At room temper-
ature, they actually “work” with a single supply at near
or below +1.7V, although as supply voltage decreases,
switch on-resistance and switching times become very
high.
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs (NO) and by COM. If power-supply
sequencing is not possible, add two small signal diodes
(D1, D2) in series with the supply pins for overvoltage
protection (Figure 1).
Adding diodes reduces the analog signal range to one
diode drop below V+ and one diode drop above V-, but
does not affect the devices’ low switch resistance and
low leakage characteristics. Device operation is
unchanged, and the difference between V+ and V-
should not exceed 17V. These protection diodes are
not recommended when using a single supply if signal
levels must extend to ground.
High-Frequency Performance
In 50
systems, signal response is reasonably flat up
to 50MHz (see Typical Operating Characteristics).
Above 20MHz, the on response has several minor
peaks which are highly layout dependent. The problem
is not turning the switch on, but turning it off. The off-
state switch acts like a capacitor, and passes higher
frequencies with less attenuation. At 10MHz, off isola-
tion is about -45dB in 50
systems, becoming worse
(approximately 20dB per decade) as frequency
increases. Higher circuit impedances also make off iso-
lation worse. Adjacent channel attenuation is about 3dB
above that of a bare IC socket, and is entirely due to
capacitive coupling.
Low-Voltage, CMOS Analog
Multiplexers/Switches
12
______________________________________________________________________________________
COM
NO
V-
V+
* INTERNAL PROTECTION DIODES
D2
D1
EXTERNAL BLOCKING DIODE
V-
V+
MAX4051/A
MAX4052/A
MAX4053/A
*
Figure 1. Overvoltage Protection Using External Blocking
Diodes
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4066CSD | IC SWITCH QUAD SPST 14SOIC |
| MAX4079CWG+ | IC A/V BACKEND 24-SOIC |
| MAX4144EEE+T | IC RX DIFF LINE HS 16-QSOP |
| MAX4356ECD+T | IC VIDEO CROSSPOINT SWIT 128TQFP |
| MAX4357ECD+TD | IC VIDEO CROSSPOINT SWIT 128TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4051D | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Low-Voltage, CMOS Analog Multiplexers/Switches |
| MAX4051EEE | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX4051EEE+ | 功能描述:多路器开关 IC 8:1 Low Voltage Analog MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX4051EEE+T | 功能描述:多路器开关 IC 8:1 Low Voltage Analog MUX RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MAX4051EEE-T | 功能描述:多路器开关 IC RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。