- 您现在的位置：买卖IC网 > PDF目录2157 > MAX4181EUT+T (Maxim Integrated Products)IC AMP CURRENT SENSE SOT23-6 PDF资料下载
参数资料
| 型号： | MAX4181EUT+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC AMP CURRENT SENSE SOT23-6 |
| 标准包装： | 2,500 |
| 放大器类型： | 电流反馈 |
| 电路数： | 1 |
| 转换速率： | 320 V/µs |
| -3db带宽： | 270MHz |
| 电流 - 输入偏压： | 1µA |
| 电压 - 输入偏移： | 1500µV |
| 电流 - 电源： | 1mA |
| 电流 - 输出 / 通道： | 60mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 11 V，±2.25 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 带卷 (TR) |
MAX4180–MAX4187
Single/Dual/Quad, 270MHz, 1mA, SOT23,
Current-Feedback Amplifiers with Shutdown
16
______________________________________________________________________________________
Keep lines as short and as straight as possible.
Do not make 90° turns; round all corners.
Observe high-frequency bypassing techniques to
maintain the amplifiers’ accuracy. The bypass cap-
acitors should include a 0.01F to 0.1F ceramic
capacitor between each supply pin and the ground
plane, located as close to the package as possible.
Place a 1F ceramic capacitor in parallel with each
0.01F to 0.1F capacitor as close to them as
possible.
Place a 10F to 15F low-ESR tantalum at the point
of entry to the power-supply pins’ PC board. The
power-supply trace should lead directly from the
tantalum capacitor to the VCC and VEE pins.
Keep PC traces short and use surface-mount com-
ponents to minimize parasitic inductance.
Maxim’s High-Speed Evaluation Board
Figures 2 and 3 show layouts of Maxim’s high-speed
single SOT23 and SO evaluation boards. These boards
were developed using the techniques described above.
The smallest available surface-mount resistors were
used for feedback and back-termination to minimize
their distance from the part, reducing the capacitance
associated with longer lead lengths.
SMA connectors were used for best high-frequency
performance. Because distances are extremely short,
performance is unaffected by the fact that inputs and
outputs do not match a 50
line. However, in applica-
tions that require lead lengths greater than one-quarter
of the wavelength of the highest frequency of interest,
use constant-impedance traces.
Fully assembled evaluation boards are available for the
MAX4180ESA.
Figure 2a. SOT23 High-Speed EV Board
Component Placement Guide—
Component Side
Figure 2b. SOT23 High-Speed EV Board
Layout—Component Side
Figure 2c. High-Speed EV Board Layout—
Solder Side
Figure 3a. SO-8 High-Speed EV Board
Component Placement Guide—
Component Side
Figure 3b. SO-8 High-Speed EV Board
Layout—Component Side
Figure 3c. SO-8 High-Speed EV Board
Layout—Solder Side
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4197ESA | IC AMP INSTR PREC R-TO-R 8-SOIC |
| MAX4198ESA+T | IC AMP DIFF PREC R-R 8-SOIC |
| MAX419ESD+T | IC OP AMP QUAD SS 14-SOIC |
| MAX4201ESA | IC BUFF OPENLOOP HS LN LP 8-SOIC |
| MAX4206ETE+ | IC AMP TRANS LOG 16-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4182 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single/Dual/Quad.270MHz.1mA.SOT23.Current-Feedback Amplifiers with Shutdown |
| MAX4182ESA | 功能描述:视频放大器 RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX4182ESA+ | 功能描述:视频放大器 270MHz 1mA Current-Feedback RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX4182ESA+T | 功能描述:视频放大器 270MHz 1mA Current-Feedback RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX4182ESA-T | 功能描述:视频放大器 RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。