- 您现在的位置：买卖IC网 > PDF目录10834 > MAX4188ESD+T (Maxim Integrated Products)IC AMP CURRENT SENSE 14-SOIC PDF资料下载
参数资料
| 型号： | MAX4188ESD+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/23页 |
| 文件大小： | 0K |
| 描述： | IC AMP CURRENT SENSE 14-SOIC |
| 标准包装： | 2,500 |
| 应用： | 电流反馈 |
| 电路数： | 3 |
| -3db带宽： | 200MHz |
| 转换速率： | 350 V/µs |
| 电流 - 电源： | 1.5mA |
| 电流 - 输出 / 通道： | 55mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 11 V，±2.25 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 带卷 (TR) |
MAX4188/MAX4189/MAX4190
Single/Triple, Low-Glitch, 250MHz, Current-
Feedback Amplifiers with High-Speed Disable
______________________________________________________________________________________
17
VOUT
RG
RS
VOUT = -(RF / RG) (VIN)
VIN
RF
RO
RT
MAX4188
MAX4189
MAX4190
Figure 3a. Inverting Gain Configuration
VOUT
RG
RS
VOUT = [1+ (RF / RG)] VIN
VIN
RF
RO
RT
MAX4188
MAX4189
MAX4190
Figure 3b. Noninverting Gain Configuration
Layout and Power-Supply Bypassing
As with all wideband amplifiers, a carefully laid out PCB
and adequate power-supply bypassing are essential to
realizing the optimum AC performance of MAX4188/
MAX4189/MAX4190. The PC board should have at
least two layers. Signal and power should be on one
layer. A large low-impedance ground plane, as free of
voids as possible, should be the other layer. With multi-
layer boards, locate the ground plane on a layer that
incorporates no signal or power traces.
Do not use wire-wrap boards or breadboards and
sockets. Wire-wrap boards are too inductive.
Breadboards and sockets are too capacitive. Surface-
mount components have lower parasitic inductance
and capacitance, and are therefore preferable to
through-hole components. Keep lines as short as pos-
sible to minimize parasitic inductance, and avoid 90°
turns. Round all corners. Terminate all unused amplifier
inputs to ground with a 100 or 150 resistor.
The MAX4188/MAX4189/MAX4190 achieve a high
degree of off-isolation (65dB at 10MHz) and low
crosstalk (-55dB at 10MHz). The input and output sig-
nal traces must be kept from overlapping to achieve
high off-isolation. Coupling between the signal traces of
different channels will degrade crosstalk. The signal
traces of each channel should be kept from overlap-
ping with the signal traces of the other channels.
Adequate bypass capacitance at each supply is very
important to optimize the high-frequency performance of
these amplifiers. Inadequate bypassing will also
degrade crosstalk rejection, especially with heavier
loads. Use a 1F capacitor in parallel with a 0.01F to
0.1F capacitor between each supply pin and ground to
achieve optimum performance. The bypass capacitors
should be located as close to the device as possible. A
10F low-ESR tantalum capacitor may be required to
produce the best settling time and lowest distortion
when large transient currents must be delivered to a
load.
Choosing Feedback and Gain Resistors
The optimum value of the external-feedback (RF) and
gain-setting (RG) resistors used with the MAX4188/
MAX4189/MAX4190 depends on the closed-loop gain
and the application circuit’s load. Table 1 lists the opti-
mum resistor values for some specific gain configura-
tions. One-percent resistor values are preferred to
maintain consistency over a wide range of production
lots. Figures 3a and 3b show the standard inverting
and noninverting configurations. Note that the nonin-
verting circuit gain (Figure 3b) is 1 plus the magnitude
of the inverting closed-loop gain. Otherwise, the two
circuits are identical.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4188EEE+T | IC AMP CURRENT SENSE 16-QSOP |
| JBXED0G02FCSDSR | CONN RCPT PROTRUDING 2POS CRIMP |
| MAX4190ESA+T | IC AMP CURRENT SENSE 8-SOIC |
| MAX4189ESD+T | IC AMP CURRENT SENSE 14-SOIC |
| MAX4258EUA+T | IC AMP VIDEO MUX 2CH 8-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4188EVKIT | 功能描述:放大器 IC 开发工具 RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX4189 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single/Triple, Low-Glitch, 250MHz, Current-Feedback Amplifiers with High-Speed Disable |
| MAX4189EEE | 功能描述:视频放大器 RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX4189EEE+ | 功能描述:视频放大器 250MHz 1.5mA Current-Feedback RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX4189EEE+T | 功能描述:视频放大器 250MHz 1.5mA Current-Feedback RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。