- 您现在的位置：买卖IC网 > PDF目录22259 > MAX4211DETE+ (Maxim Integrated)IC CURRENT MONITOR 1.5% 16TQFN PDF资料下载
参数资料
| 型号： | MAX4211DETE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 20/32页 |
| 文件大小： | 0K |
| 描述： | IC CURRENT MONITOR 1.5% 16TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 功能： | 电流监控器 |
| 检测方法： | 高端 |
| 精确度： | ±0.5% |
| 输入电压： | 4 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（4x4） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
High-Side Power and
Current Monitors
The common-mode voltage range is +4V to +28V and
independent of the supply voltage. With this feature, the
device can monitor the output current of a high-voltage
source while running at a lower system voltage typically
between 2.7V and 5.5V.
The MAX4211 has a current-sense amplifier output. The
voltage at IOUT is proportional to the voltage across
V SENSE :
V IOUT = A VIOUT x V SENSE
where V SENSE is the voltage across RS+ and RS-, and
A VIOUT is the amplifier gain of the device given in Table 1.
Analog Multiplier
The MAX4210/MAX4211 integrate an analog multiplier
that enables real-time monitoring of power delivered to
a load. The voltage proportional to the load current is
fed to one input of the multiplier and a voltage propor-
tional to the source voltage is fed to the other. The ana-
log multiplier multiplies these two voltages to obtain an
output voltage proportional to the load power. The ana-
log multiplier is designed only to operate in the positive
quadrant, that is, the inputs and outputs are always
positive voltages.
For the MAX4210D/E/F and MAX4211D/E/F, the analog
multiplier full-scale input at IN is approximately 1V. This
independent multiplier input allows greater design flexi-
bility when using an external voltage-divider. For the
MAX4210A/B/C and MAX4211A/B/C, an integrated volt-
age-divider divides the source voltage at the RS+ pin
by a nominal value of 25 and passes this voltage to the
multiplier. Thus, the full-scale input voltage at RS+ is
25V. The integrated, trimmed resistor-dividers reduce
external component count and cost.
The voltage output at POUT is proportional to the output
where V SENSE is the voltage across RS+ and RS- and
A VPOUT is the amplifier gain of the device given in
Table 2.
Internal Comparators (MAX4211)
The MAX4211 features two uncommitted open-drain
output comparators. These comparators can be config-
ured to trip when load current or power reaches a set
limit. They can also be configured as a window com-
parator with wire-OR output. Comparator 1 (COUT1)
features latch-enable (LE) and inhibit (INHIBIT) inputs.
When LE is low, the comparator is transparent (it func-
tions as a regular unlatched comparator). When LE is
high, the comparator output (COUT1) is latched. When
high, the INHIBIT input suspends the comparator oper-
ation and latches the output to the current state. The
operation of INHIBIT is similar to LE, except it has a dif-
ferent input threshold and wider hysteresis. The INHIB-
IT logic-high threshold is 1.21V and logic-low threshold
is 0.6V with 0.6V hysteresis. INHIBIT is useful in pre-
venting the comparator from giving false output during
fast RS+ transients. INHIBIT is generally triggered by
an RC network connected to RS+ (see the Applications
Information ). Both comparators have a built-in 300μs
blanking period at power-up to prevent false outputs.
The comparator outputs are open drain and they can
be pulled up to V CC , RS+, or any voltage less than
+28V. LE and INHIBIT are internally pulled down by a
1μA source.
Table 2. MAX4210/MAX4211 Power-Sense
Amplifier Gain and Full-Scale Sense
Voltage
power:
POWER-SENSE
FULL-SCALE
For the MAX4210A/B/C and MAX4211A/B/C:
V POUT = A VPOUT x V SENSE x V RS+
For the MAX4210D/E/F and MAX4211D/E/F:
V POUT = A VPOUT x V SENSE x V IN
Table 1. MAX4211 Current-Sense
Amplifier Gain and Full-Scale Sense
Voltage
PART
MAX4210A
MAX4210B
MAX4210C
MAX4210D
MAX4210E
MAX4210F
AMPLIFIER GAIN
(A VPOUT , 1/V)
0.667
1.000
1.640
16.670
25.000
40.960
SENSE VOLTAGE
(mV)
150
150
100
150
150
100
CURRENT-SENSE
FULL-SCALE
MAX4211A
0.667
150
PART
MAX4211A/D
MAX4211B/E
MAX4211C/F
AMPLIFIER GAIN
(A VIOUT , V/V)
16.67
25.00
40.96
SENSE VOLTAGE
(mV)
150
150
100
MAX4211B
MAX4211C
MAX4211D
MAX4211E
MAX4211F
1.000
1.640
16.670
25.000
40.960
150
100
150
150
100
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| RSA44DTKI-S288 | CONN EDGECARD 88POS .125 EXTEND |
| GP08JHE3/73 | DIODE 0.8A 600V STD SMC |
| ASM02DRTN | CONN EDGECARD 4POS DIP .156 SLD |
| VE-B3B-EU-F3 | CONVERTER MOD DC/DC 95V 200W |
| AISC-1008F-1R2J-T | INDUCTOR WW FERRITE 1200NH 1008 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4211DETE+ | 功能描述:电流和电力监控器、调节器 High-Side Power & Current Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX4211DETE+T | 功能描述:电流和电力监控器、调节器 High-Side Power & Current Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX4211DETE-T | 功能描述:电流和电力监控器、调节器 High-Side Power & Current Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX4211DEUE | 功能描述:电流和电力监控器、调节器 High-Side Power & Current Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
| MAX4211DEUE+ | 功能描述:电流和电力监控器、调节器 High-Side Power And Current Monitor RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。