- 您现在的位置：买卖IC网 > PDF目录20059 > MAX4273EEE+ (Maxim Integrated)IC CNTRLR HOT SWAP 16-QSOP PDF资料下载
参数资料
| 型号： | MAX4273EEE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 19/26页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR HOT SWAP 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 2.7 V ~ 13.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
3V to 12V Current-Limiting Hot-Swap Controllers
with Autoretry, DualSpeed/BiLevel Fault Protection
MOSFET with a duty cycle equal to t ON/ t RETRY and with
a current equal to I FAST,SET . Therefore, particular care
has to be taken when choosing between immediate
retry and board space needed to manage the power
dissipation capabilities of the MOSFET (see Thermal
Considerations ). The duty cycle is fixed to 1/32 for the
MAX4272, but can be varied in the MAX4273 by choos-
ing CTIM and C TON independently.
Additional External Gate Capacitance (CEXT)
An external gate capacitance can be connected at
GATE. This increases the time required to enhance the
MOSFET and further limits the output rise time. In the
MAX4271/MAX4272, connect the external capacitor
between GATE and GND. In the MAX4273, the external
capacitor can be connected between GATE and CEXT
or GND. If the capacitor is connected to CEXT, it is dis-
charged to ground during a slow comparator fault but it
is left floating during a fast comparator fault; this allows
the device to turn off the external MOSFET faster during
critical faults. (CEXT is biased at V IN ; therefore, use a
nonpolarized capacitor). Capacitance connected from
GATE to CEXT does little to decrease the regulated cur-
rent ripple. Add a small capacitor (5nF) from GATE to
GND. See the charging and discharging time vs. C GATE
graphs in the Typical Operating Characteristics .
Slow Comparator Response Time (CSPD)
The slow comparator threshold is set at 50mV, and its
response time is determined by the external capacitor
connected to CSPD (Figure 10).
A minimum response time of 20μs (typ) is achieved by
leaving this pin floating. This time is determined inter-
nally and is not affected by stray capacitance at CSPD
(up to 100pF).
SLOW COMPARATOR
Set the slow comparator response time to be longer
than the normal operation load transients (see Slow
Comparator ).
ON and Reset Comparators
The ON comparator controls the ON/OFF function of
these devices. The ON comparator is a precision volt-
age comparator that can be used for temperature moni-
toring or as an additional UVLO (Figure 11). The
MAX4273 also features an uncommitted delayed com-
parator. This comparator can be used for voltage moni-
toring, power sequencing, or for generating a power-on
reset signal for on-card microprocessors (Figure 12).
Both comparator threshold voltages are set at V REF /2 =
0.6V with a 3mV (typ) hysteresis.
The uncommitted comparator OUTC output is an open-
drain output, and it is asserted low when its input volt-
age (INC) is below the threshold voltage. It goes into a
high-impedance state 150ms after the voltage has risen
above the threshold. The delay for negative-going
edges is 10μs.
Figure 13 shows the MAX4273 used to monitor precise-
ly the temperature of an external device such as the
MOSFET. This configuration uses the uncommitted
comparator to set the UVLO at a higher level by running
its output into the ON comparator’s input.
The ON comparator initiates startup when its input volt-
age (V ON ) rises above the threshold voltage and turns
off the MOSFET when the voltage falls below the thresh-
old. The propagation delay is 10μs going high or low.
The ON comparator is also used to reset the
MAX4271/MAX4273 (when CTIM = V IN ) after a fault
condition (see Latched/Autoretry ).
V REF
1000
100
10
RESPONSE TIME vs. CSPD
t CSPD (ms) = 0.2 x CSPD (nF)
R1
ON
MAX4271
MAX4272
MAX4273
LOGIC
CONTROL
1
NTC
R2
0.6V
0.1
0.01
0.01
0.1
1 10
CSPD (nF)
100
1000
R1 = R2 ? (V REF / O.6 - 1)
R2 = VALUE OF THE NTC RESISTOR AT THE LIMIT TEMPERATURE
V REF = ANY REFERENCE VOLTAGE AVAILABLE OR V IN
Figure 10. Slow Comparator Response Time vs. CSPD
Figure 11. Temperature Monitoring and Protection
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| ISL9011IRBBZ-T | IC REG LDO 1.5V .15A/.3A 10-DFN |
| MAX5954AETX+ | IC PCI EXP/HOT-PLUG CTRLR 36TQFN |
| GRM216R71H103KA01D | CAP CER 10000PF 50V 10% X7R 0805 |
| VE-2T1-CX | CONVERTER MOD DC/DC 12V 75W |
| HR-DF8 | BATT PACK 9.6V D 6500MAH NIMH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4273EEE+ | 功能描述:热插拔功率分布 3-12V Current-Limit Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX4273EEE+T | 功能描述:热插拔功率分布 3-12V Current-Limit Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX4273EEE-T | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX4273ESE | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX4273ESE+ | 功能描述:热插拔功率分布 3-12V Current-Limit Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。