- 您现在的位置：买卖IC网 > PDF目录2157 > MAX4278ESA+T (Maxim Integrated Products)IC BUFFER CLOSE LOOP 8SOIC PDF资料下载
参数资料
| 型号： | MAX4278ESA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC BUFFER CLOSE LOOP 8SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 缓冲器 |
| 电路数： | 1 |
| 转换速率： | 1600 V/µs |
| -3db带宽： | 310MHz |
| 电流 - 输入偏压： | 1µA |
| 电压 - 输入偏移： | 500µV |
| 电流 - 电源： | 8mA |
| 电流 - 输出 / 通道： | 100mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
MAX4178/MAX4278
330MHz, Gain of +1/Gain of +2
Closed-Loop Buffers
8
______________________________________________________________________________________
Applications Information
Grounding, Bypassing,
and PC Board Layout
In order to obtain the MAX4178/MAX4278s’ full 330MHz/
310MHz bandwidths, microstrip and stripline tech-
niques are recommended in most cases. To ensure
that the PC board does not degrade the amplifier’s per-
formance, it’s a good idea to design the board for a fre-
quency greater than 1GHz. Even with very short traces,
it’s good practice to use these techniques at critical
points, such as inputs and outputs. Whether you use a
constant-impedance board or not, observe the follow-
ing guidelines when designing the board:
Do not use wire-wrap boards. They are too inductive.
Do not use IC sockets. They increase parasitic capaci-
tance and inductance.
In general, surface-mount components have shorter
leads and lower parasitic reactance, giving better
high-frequency performance than through-hole com-
ponents.
The PC board should have at least two layers, with
one side a signal layer and the other a ground plane.
Keep signal lines as short and straight as possible.
Do not make 90° turns; round all corners.
The ground plane should be as free from voids as
possible.
On Maxim’s evaluation kit, the ground plane has been
removed from areas where keeping the trace capaci-
tance to a minimum is more important than maintaining
ground continuity.
Driving Capacitive Loads
The MAX4178/MAX4278 provide maximum AC perfor-
mance with no output load capacitance. This is the
case when the MAX4178/MAX4278 are driving a cor-
rectly terminated transmission line (e.g., a back-termi-
nated 75
cable). However, the MAX4178/MAX4278
are capable of driving capacitive loads up to 100pF
without oscillations, but with reduced AC performance.
Driving large capacitive loads increases the chance of
oscillations in most amplifier circuits. This is especially
true for circuits with high loop gains, such as voltage
followers. The amplifier’s output resistance and the load
capacitor combine to add a pole and excess phase to
the loop response. If the frequency of this pole is low
enough and if phase margin is degraded sufficiently,
oscillations may occur.
A second problem when driving capacitive loads
results from the amplifier’s output impedance, which
looks inductive at high frequency. This inductance
forms an L-C resonant circuit with the capacitive load,
which causes peaking in the frequency response and
degrades the amplifier’s gain margin.
The MAX4178/MAX4278 drive capacitive loads up to
100pF without oscillation. However, some peaking (in
the frequency domain) or ringing (in the time domain)
may occur. This is shown in Figures 2a and 2b and the
in the Small- and Large-Signal Pulse Response graphs
in the Typical Operating Characteristics.
To drive larger-capacitance loads or to reduce ringing,
add an isolation resistor between the amplifier’s output
and the load, as shown in Figure 1.
The value of RISO depends on the circuit’s gain and the
capacitive load. Figures 3a and 3b show the Bode
plots that result when a 20
isolation resistor is used
with a voltage follower driving a range of capacitive
loads. At the higher capacitor values, the bandwidth is
dominated by the RC network, formed by RISO and CL;
the bandwidth of the amplifier itself is much higher.
Note that adding an isolation resistor degrades gain
accuracy. The load and isolation resistor form a divider
that decreases the voltage delivered to the load.
MAX4178
MAX4278
VIN
RISO
VOUT
CL
RL
Figure 1. Capacitive-Load Driving Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4289ESA+T | IC OP AMP SNGL 8-SOIC |
| MAX4294EUD+T | IC OP AMP R-R I/O 14-TSSOP |
| MAX4305ESA+ | IC OP AMP LOW NOISE 8-SOIC |
| MAX430EPA | IC OPAMP +/-15V CHOP/STAB 8-DIP |
| MAX4321EUK-T | IC OPAMP 5MHZ R-TO-R I/O SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4278EUA | 功能描述:IC BUFF CLOSE/LOOP 310MHZ 8-UMAX RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有关文件:Automotive Product Guide 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 放大器类型:通用 电路数:1 输出类型:满摆幅 转换速率:3 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:2.5mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:Digi-Reel® 其它名称:MAX4475AUT#TG16DKR |
| MAX4278EUA+ | 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4278EUA+T | 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4278EUA-T | 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4278EUK | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。