- 您现在的位置：买卖IC网 > PDF目录3324 > MAX4432EUA+T (Maxim Integrated Products)IC OP AMP DUAL 180MHZ 8UMAX PDF资料下载
参数资料
| 型号： | MAX4432EUA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP DUAL 180MHZ 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 放大器类型： | 电压反馈 |
| 电路数： | 2 |
| 转换速率： | 100 V/µs |
| -3db带宽： | 180MHz |
| 电流 - 输入偏压： | 11µA |
| 电压 - 输入偏移： | 1250µV |
| 电流 - 电源： | 11mA |
| 电流 - 输出 / 通道： | 60mA |
| 电压 - 电源，单路/双路(±)： | 9 V ~ 11 V，±4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
Detailed Description
The MAX4430–MAX4433 are wide-bandwidth, ultra-low-
distortion, voltage-feedback amplifiers. The MAX4430/
MAX4432 are internally compensated for unity gain.
The MAX4431/MAX4433 are internally compensated for
gains of +2V/V or greater.
These amplifiers have ultra-fast 37ns (MAX4430/
MAX4432) 16-bit settling times, 100dB SFDR at 1MHz,
and 4Vp-p output swing with minimum 110dB open-
loop gain.
High-Speed ADC Input Driver Application
The MAX4430–MAX4433 op amps are ideal for driving
high-speed 14- to 16-bit ADCs. In most cases, these
ADCs operate with a charge balance scheme, with
capacitive loads internally switched on and off from the
input. The driver used must withstand these changing
capacitive loads while holding the signal amplitude sta-
bility consistent with the ADC’s resolution and, at the
same time, have a frequency response compatible with
the sampling speed of the ADC (Figure 1).
Inverting and Noninverting Configurations
The circuits typically used for the inverting and non-
inverting configurations of the MAX4430–MAX4433 are
shown in Figures 2a and 2b. The minimum uncondition-
ally stable gain values are 1 for the MAX4430/MAX4432
and 2 for the MAX4431/MAX4433. Use care in selecting
the value for the resistor marked RS in both circuits.
From dynamic stability considerations (based on the
part’s frequency response and the input capacitance of
the MAX4430–MAX4433), the maximum recommended
value for RS is 500
. In general, lower RS values will
yield a higher bandwidth and better dynamic stability,
at the cost of higher power consumption, higher power
dissipation in the IC, and reduced output drive avail-
ability. For a minimum RS value, take into consideration
that the current indicated as IF is supplied by the output
stage and must be discounted from the maximum out-
put current to calculate the maximum current available
to the load. IF can be found using the following equa-
tion:
IF = VIN(MAX) / RS
If DC thermal stability is an important design concern,
the Thevenin resistance seen by both inputs at DC
must be balanced. This includes the resistance of the
signal source and termination resistors if the amplifier
signal input is fed from a transmission line. The capaci-
tance associated with the feedback resistors must also
be considered as a possible limitation to the available
bandwidth or to the dynamic stability. Only resistors
with small parallel capacitance specifications should
be considered.
Applications Information
Layout and Power-Supply Bypassing
The MAX4430–MAX4433 have wide bandwidth and
consequently require careful board layout. To realize
the full AC performance of these high-speed amplifiers,
pay careful attention to power-supply bypassing and
board layout. The PC board should have a large low-
impedance ground plane that is as free of voids as
possible. Do not use commercial breadboards. Keep
signal lines as short and straight as possible. Observe
high-frequency bypassing techniques to maintain the
MAX4430–MAX4433
Dual-Supply, 180MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
_______________________________________________________________________________________
9
+VCC
-VEE
HIGH-SPEED
14/16-BIT ADC
Figure 1. Typical Application Circuit
VOUT
VIN
RS
RF
IF
RF
RS
VOUT
VIN
=
A = 1 +
Figure 2a. Noninverting Configuration
- RF
RS
VOUT
VIN
VOUT
VIN
RB
RF
RS
IF
=
A =
Figure 2b. Inverting Configuration
相关PDF资料 |
PDF描述 |
|---|---|
| 10-89-1281 | CONN HEADER 28POS .100 VERT GOLD |
| MAX4333EUB+T | IC OP AMP R-R I/O LP 10-UMAX |
| BK1/GMA-315-R | FUSE .315A 250V FST GLASS UL CSA |
| 0031.1907 | FUSE HOLDER FEF F'GRIP IP40 |
| 0031.1091 | FUSEHOLDER FOR 5X20 SLOT PNL MNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4433ESA | 功能描述:运算放大器 - 运放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4433ESA-T | 功能描述:运算放大器 - 运放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4433EUA | 功能描述:运算放大器 - 运放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4433EUA+ | 功能描述:运算放大器 - 运放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4433EUA+T | 功能描述:运算放大器 - 运放 Dual-Supply 180MHz 16-Bit Accurate RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。