- 您现在的位置：买卖IC网 > PDF目录2158 > MAX4437EUA+T (Maxim Integrated Products)IC OP AMP DUAL 150MHZ 8UMAX PDF资料下载
参数资料
| 型号： | MAX4437EUA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/14页 |
| 文件大小： | 0K |
| 描述： | IC OP AMP DUAL 150MHZ 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 放大器类型： | 电压反馈 |
| 电路数： | 2 |
| 转换速率： | 388 V/µs |
| -3db带宽： | 150MHz |
| 电流 - 输入偏压： | 14µA |
| 电压 - 输入偏移： | 1000µV |
| 电流 - 电源： | 15mA |
| 电流 - 输出 / 通道： | 65mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
MAX4434–MAX4437
Single-Supply, 150MHz, 16-Bit Accurate,
Ultra-Low Distortion Op Amps
_______________________________________________________________________________________
9
Detailed Description
The MAX4434–MAX4437 are wide-bandwidth, ultra-low-
distortion, voltage-feedback amplifiers. The MAX4434/
MAX4436 are internally compensated for unity gain.
The MAX4435/MAX4437 are internally compensated for
gains of +5V/V or greater.
These amplifiers have ultra-fast 35ns (MAX4434/
MAX4436) 16-bit settling times, -97dB SFDR at 1MHz,
and 4Vp-p output swing with minimum 115dB open-
loop gain.
High-Speed ADC Input Driver Application
The MAX4434–MAX4437 op amps are ideal for driving
high-speed 14- to 16-bit ADCs. In most cases, these
ADCs operate with a charge balance scheme, with
capacitive loads internally switched on and off from the
input. The driver used must withstand these changing
capacitive loads while holding the signal amplitude sta-
bility consistent with the ADC’s resolution and, at the
same time, have a frequency response compatible with
the sampling speed of the ADC (Figure 1).
Inverting and Noninverting Configurations
The circuits typically used for the inverting and non-
inverting configurations of the MAX4434–MAX4437 are
shown in Figures 2a and 2b. The minimum uncondition-
ally stable gain values are 1 for the MAX4434/MAX4436
and 5 for the MAX4435/MAX4437. Use care in selecting
the value for the resistor marked RS in both circuits. From
dynamic stability considerations (based on the part’s fre-
quency response and the input capacitance of the
MAX4434–MAX4437), the maximum recommended
value for RS is 500
Ω. In general, lower RS values will
yield a higher bandwidth and better dynamic stability, at
the cost of higher power consumption, higher power dis-
sipation in the IC, and reduced output drive availability.
For a minimum RS value, take into consideration that the
current indicated as IF is supplied by the output stage
and must be discounted from the maximum output cur-
rent to calculate the maximum current available to the
load. IF can be found using the following equation:
IF = VIN(MAX) / RS
If DC thermal stability is an important design concern,
the Thevenin resistance seen by both inputs at DC
must be balanced. This includes the resistance of the
signal source and termination resistors if the amplifier
signal input is fed from a transmission line. The capaci-
tance associated with the feedback resistors must also
be considered as a possible limitation to the available
bandwidth or to the dynamic stability. Only resistors
with small parallel capacitance specifications should
be considered.
Applications Information
Layout and Power-Supply Bypassing
The MAX4434–MAX4437 have wide bandwidth and
consequently require careful board layout. To realize
the full AC performance of these high-speed amplifiers,
pay careful attention to power-supply bypassing and
board layout. The PC board should have a large low-
impedance ground plane that is as free of voids as
possible. Do not use commercial breadboards. Keep
signal lines as short and straight as possible. Observe
high-frequency bypassing techniques to maintain the
amplifier’s accuracy and stability. In general, use sur-
VCC
VEE
HIGH-SPEED
14/16-BIT ADC
Figure 1. Typical Application Circuit
VOUT
VIN
RS
RF
IF
RF
RS
VOUT
VIN
=
A = 1 +
Figure 2a. Noninverting Configuration
- RF
RS
VOUT
VIN
VOUT
VIN
RB
RF
RS
IF
=
A =
Figure 2b. Inverting Configuration
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4451ESA+T | IC OP AMP R-R DUAL 210MHZ 8-SOIC |
| MAX4454ESD+T | IC OPAMP SNGL R-R OUT 14-SOIC |
| MAX4460EUT#TG16 | IC INSTR AMP SGL R-R SOT-23-6 |
| MAX4472EUD+T | IC OP AMP QUAD R-R 9KHZ 14-TSSOP |
| MAX4475AUT#TG16 | IC OP AMP R-R LN 10MHZ SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX44420MJA/883 | 制造商:Maxim Integrated Products 功能描述: |
| MAX4444ESE | 功能描述:仪表放大器 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
| MAX4444ESE/GG8 | 制造商:Maxim Integrated Products 功能描述:ULTRA-HIGH-SPEED, LOW-DISTORTION, DIFFERENTIAL-TO-SINGLE-END - Rail/Tube |
| MAX4444ESE+ | 功能描述:仪表放大器 6500V/uM 400MHz Line Receiver RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
| MAX4444ESE+ | 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR ((NW)) |
发布紧急采购，3分钟左右您将得到回复。