- 您现在的位置：买卖IC网 > PDF目录18728 > MAX4473ESA (Maxim Integrated)IC AMP PA PWR GSM CONTROL 8-SOIC PDF资料下载
参数资料
| 型号： | MAX4473ESA |
| 厂商： | Maxim Integrated |
| 文件页数： | 5/9页 |
| 文件大小： | 0K |
| 描述： | IC AMP PA PWR GSM CONTROL 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| RF 型： | GSM |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
Low-Cost, Low-Voltage, PA Power Control
Amplifier for GSM Applications
Pin Description
PIN
1
2
3
4
5
6
7
8
NAME
SR1
SR2
SHDN
PC
GND
SR3
OUT
VCC
FUNCTION
Inverting Input of Error Amplifier and Drain of V-to-I FET, Q1. Connect to supply side of current-sense
resistor, R SENSE , through gain resistor RG1.
Noninverting Input of Error Amplifier. Connect to load side of current-sense resistor, R SENSE , through
gain resistor RG2. Set RG2 equal to RG1.
Shutdown Input. Drive SHDN low to disable all amplifiers, pull OUT to GND, set the gate-to-source
voltage of the V-to-I FET (Q1) to 0, and reduce supply current to less than 1μA. Drive high or connect
to V CC for normal operation.
Power Control Input. Apply a voltage to PC to set a DC current through the sense resistor to control
PA bias.
Ground
Inverting Input to V-to-I Converter and Source of V-to-I FET, Q1. Connect to ground through gain
resistor RG3.
Output of Error Amplifier. Connect to gain control pin of power amplifier in bias control applications.
+2.7V to +6.5V Voltage Supply Input. Bypass to ground with a 0.1μF capacitor.
Detailed Description
The MAX4473 is a voltage-controlled, unidirectional,
high-side current setting amplifier for applications
where accurate control of PA supply current is desired.
This device is intended for wireless TDMA based sys-
tems (GSM, DECT), where tight restrictions over the
PA’s transmit burst and output power require closed-
loop control over the PA’s output power. When used
with a PA, the MAX4473 functions as a voltage-con-
trolled constant current source, accurately setting PA
supply current by varying the gain of the PA. If you
know the output power versus supply current profile for
the PA, you can set the PA’s output power by control-
ling the amount of supply current delivered to the PA.
The MAX4473 is composed of an input buffer (A1), a
voltage-to-current converting amplifier (A2), and a rail-
to-rail output error amplifier (A3) (see Typical Operating
Circuit). External gain and sense resistors allow pro-
grammability for a wide range of applications.
In the Typical Operating Circuit , PA supply current
flows from the system supply, through the external cur-
rent-sense resistor (R SENSE ), to the PA. The rail-to-rail
outputs of the error amplifier, A3, adjust the gain of the
PA until the voltage drop across R SENSE equals the
voltage drop across external gain resistor, RG1. The
voltage drop across RG1 sets the voltage drop across
R SENSE , with a larger voltage drop resulting in more
current delivered to the PA. The voltage drop across
RG1 is set by A1, A2, and the V-to-I FET, Q1. A voltage
applied to the PC input of the input buffer is divided by
four by a resistor-divider network. A2 forces its inverting
input and the source of Q1 to V PC / 4, thus setting a
voltage across RG3. The resulting current through RG3
sets the current through RG1. This unique architecture
allows the supply current to be set independent of sup-
ply voltage. Set PA supply current according to the fol-
lowing equation:
I CCPA = ( V PC · RG1 ) / ( 4 · R SENSE · RG3 )
Shutdown Mode
When SHDN is a logic-level low ( SHDN < 0.4V), ampli-
fiers A1, A2, and A3 are off, Q1 is turned off, and the
output of A3 is actively pulled to ground with an N-
channel FET. Supply current is reduced to less than
1μA in shutdown mode. Typical power-up time is 0.9μs
and typical power-down time is 0.3μs, using the
MAX4473 test circuit.
_______________________________________________________________________________________
5
相关PDF资料 |
PDF描述 |
|---|---|
| KC2520B12.0000C10E00 | OSCILLATOR 12.0000MHZ SMD |
| 7X-1.8432MBB-T | OSC 1.8432 MHZ 3.3V SMD |
| GLCC01C | SWITCH TOP ROLLR PLNGR SNAP SPDT |
| 7X-14.31818MBB-T | OSC 14.31818 MHZ 3.3V SMD |
| GLCB04C | SWTCH TOP ROLLER PLUNGER SLO ACT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4473ESA-T | 功能描述:射频放大器 PA Power Control Amp for GSM Aps RoHS:否 制造商:Skyworks Solutions, Inc. 类型:Low Noise Amplifier 工作频率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 输出截获点:37.5 dBm 功率增益类型:32 dB 噪声系数:0.85 dB 工作电源电压:5 V 电源电流:125 mA 测试频率:2.6 GHz 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-16 封装:Reel |
| MAX4473ETA | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4473ETA-T | 制造商:Maxim Integrated Products 功能描述:LOW-COST, LOW-VOLTAGE, PA POWER CONTROL AMPLI - Tape and Reel |
| MAX4473EUA | 功能描述:功率放大器 PA Power Control Amp for GSM Aps RoHS:否 制造商:TriQuint Semiconductor 封装 / 箱体: 工作电源电压:28 V 电源电流:2.5 A 工作温度范围: 封装: |
| MAX4473EUA+ | 功能描述:功率放大器 PA Power Control Amp for GSM Aps RoHS:否 制造商:TriQuint Semiconductor 封装 / 箱体: 工作电源电压:28 V 电源电流:2.5 A 工作温度范围: 封装: |
发布紧急采购，3分钟左右您将得到回复。